JVC BR-DV600UA 45 pg user manual for BR-DV600U/E VTR (1130KB) - Page 14
Playback
View all JVC BR-DV600UA manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
6 RECORDING [REC LEVEL] control CH-1/3 REC LEVEL VIDEO CASSETTE RECORDER BR-DV600U OPERATE ON/OFF EJECT CH-2/4 MENU ADVANCE PRESET SHIFT SHIFT HOLD SHIFT A. DUB PHONES SELECT SET MONITOR OUTPUT COUNTER L CH-1/2 CTL MIX MIX TC R CH-3/4 UB AUDIO CH 1/3 40 30 20 10 CH 2/4 OVER AUTO OFF DEW 0 dB OVER SERVO RF 32k 48k SLAVE PB NDF HOLD AUD LOCK SP MENU H M S F REC PLAY PAUSE REMOTE REW STOP FF LOCAL MIC [A. DUB] button [REC] button [PLAY] button [PAUSE] button [STOP] button Audio dubbing Signals can only be recorded on CH3 and CH4. 1 Set the No. 245 menu switch to "32K". Set the No. 108 menu switch to any position except "IEEE 1394". (Audio dubbing is not possible with digital audio input.) 2 Press the [PLAY] button to play back the tape. 3 Press the [PAUSE] button at the position from which you want to start recording audio. While holding the [PAUSE] button, press the [A.DUB] button. The Audio Dubbing Pause mode cannot be engaged unless the VCR is in the Stop mode. First engage the Stop mode. Then, while holding down the [PAUSE] button, press the [A. DUB] button. • Audio dubbing If audio dubbing is disabled for any reason - for example, if a section of tape recorded using 48 kHz sampling is backspaced in the Pause mode - the "Aud inh" indication is shown and the VCR enters the Stop mode. 4 Adjust the audio recording level with the [REC LEVEL] control. 5 Press the [PLAY] button to start audio dubbing. [Audio signals are recorded on CH3 and CH4. To stop audio dubbing temporarily, press the [PAUSE] button. 6 To end audio dubbing, press the [STOP] button. 24 Notes: 5 Audio dubbing is not possible on tapes recorded with 48 kHz sampling frequency. 5 If audio dubbing is performed repeatedly on a short section of the tape, there may be some noise when this section is played back. 5 For audio dubbing, use a tape recorded with this unit. If another tape is used, first dub it to a tape on this unit. When audio is dubbed on a tape recorded on another VCR (including another BR-DV600), sound and picture may be distorted. 5 During audio dubbing, noise might be visible on the playback picture. But it is not a trouble of BR-DV600. Audio dubbing itself is proceeded normally. 5 It is not possible to use the audio dubbing function to record the CH1/2 playback signal on CH3/4 (soundon-sound) . Reference Recording section on the tape In the MiniDV format, one video frame consists of 10 tracks. Each track includes recording sections for audio, video and sub code (time code, date, time). As shown in the diagram, the audio recording section provides 2 channels or 4 channels depending on the sampling rate frequency selected. In the Audio Dubbing mode, audio signals are recorded in the CH3 and CH4 section which is created when the 32 kHz sampling frequency is selected. Sub code area Video area Audio area 48k CH1 CH2 32k CH1/CH2 CH3/CH4 7 PLAYBACK CH-1/3 REC LEVEL VIDEO CASSETTE RECORDER BR-DV600U OPERATE ON/OFF EJECT CH-2/4 MENU ADVANCE PRESET SHIFT SHIFT HOLD SHIFT A. DUB PHONES SELECT SET MONITOR OUTPUT COUNTER L CH-1/2 CTL MIX MIX TC R CH-3/4 UB AUDIO CH 1/3 40 30 20 10 CH 2/4 32k 48k SLAVE AUD LOCK SP OVER AUTO OFF DEW 0 dB OVER SERVO RF PB NDF HOLD MENU H M S F REC PLAY PAUSE REMOTE REW STOP FF LOCAL MIC [AUDIO MONITOR] switch [AUDIO OUTPUT] switch [REC] button [PLAY] button [FF] button [STOP] button [OPERATE] button [PAUSE] button Playback preparation 1 Press the [OPERATE] button to turn the power ON. 2 Insert the cassette into the cassette loading slot. 3 Select the audio output channel. Select the signals output from the [AUDIO OUT] connectors with the [AUDIO OUTPUT] switch. ੬ See "Audio system connections" on page 12. Playback 1 Press the [PLAY] button. Video and audio signals are output from each output connector. Other data recorded on the tape is read out (time code, user bits, etc.) 2 To stop playback, press the [STOP] button. 3 To temporarily stop playback, press the [PAUSE] button. • For fast-forward playback, press the [FF] button during playback. • For fast reverse playback, press the [REW] button during playback. • You can select whether or not to play sound during fast-forward playback or fast reverse playback with the No. 212 ON/OFF setting. Repeat play 1 Set the No. 311 and No. 312 menu switches to "ON". ੬ See No. and No. 312 on page 19. 2 Press the [PLAY] button to start playback. At tape end, the tape is rewound automatically and playback starts again. This operation repeats each time the tape ends. 3 To stop Repeat Play, press the [STOP] button. Notes: 5 If audio dubbing is performed repeatedly on a short section of the tape, there may be some noise when this section is played back. 5 When a tape recorded on a consumer MiniDV VCR is played back on this unit, the sound level may be low. 5 When the Pause mode continues for more than 5 minutes, the Stop mode is automatically engaged to protect the tape. If tape remaining time is less than 3 minutes or the unit is being used in a lowtemperature environment, the Stop mode is engaged within about 3 minutes. The Stop mode is also engaged automatically if slow playback continues for more than 1 minute with the remote controller or reverse slow playback continues for more than 20 seconds. 25