JVC BR-DV600UA 45 pg user manual for BR-DV600U/E VTR (1130KB) - Page 15
External, Timer-start Function, Time Code
View all JVC BR-DV600UA manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
8 EXTERNAL TIMER-START FUNCTION (AUTOMATIC START-UP WITH POWER SUPPLY) DV IN/OUT VIDEO LINE COMPONENT Y/C IN R-Y B-Y Y AUDIO CH 1/3 CH 2/4 IN IN OUT PGZ01945 OUT OUT MONITOR OUT 1 REMOTE 2 MONITOR OUT SYNC IN TIME CODE SPARE TIMER SERIAL REC PLAY DC 12V OFF REC: Timer recording OFF: Timer function OFF PLAY: Timer playback Commercially available timer, etc. When power (AC 120 V (U MODEL), AC 220 - 240 V (E MODEL) or DC 12 V) is supplied to this unit, it automatically enters the Record or Play mode. Using a commercially available timer, you can configure your VCR to start recording or playback at a specified time. Playback 1 Connect the power cable. To turn this unit ON with a commercially available timer, connect the power cable plug to the timer's power output socket. Set the front panel's [REMOTE/LOCAL] switch to "LOCAL". 2 Insert a cassette. 3 Set the rear panel's [TIMER] switch to "PLAY". 4 When power is supplied, playback starts automati- cally. Repeat playback can be set with menu switch setting. ੬ See No. and No. 312 on page 19. With the menu switches set appropriately, the tape can be rewound to the beginning before starting playback. ੬ See No. 360 on page 19. 5 Stop playback. Press the [STOP] button. Recording 1 Connect the power cable. To turn this unit ON with a commercially available timer, connect the power cable plug to the timer's power output socket. Set the front panel's [REMOTE/LOCAL] switch to "LOCAL". 2 Select the video input. 3 Adjust the audio recording level. 4 Insert a cassette. 5 Set the rear panel's [TIMER] switch to "REC". 6 When power is supplied, the VCR automatically enters the Record mode. Using the menu switches, you can set the VCR to start recording after rewinding the tape to the beginning. ੬ See No. 360 on page 19. 7 Stop recording. Press the [STOP] button. Note: 5 External timer control should only be used to start VCR operation. Do not use an external timer to turn the VCR power off while the tape is running. Doing so could damage this unit or the tape. 9 TIME CODE The time code is recorded frame by frame together with the materials to be recorded on the tape. With this time code, the position of the materials can be precisely specified, improving the editing accuracy and working efficiency. (The editing accuracy of 0 frame may not be obtained even though the time code is used, depending on the performance of the VCR and editing controller and influence of editing system.) With this system, the time code can be recorded and played back. On-screen display S TOP TCR 1 2 : 0 0 : 0 0 : 0 0 (U MODEL) : - Non-drop frame · - Drop frame TCR: TCG: UBR: UBG: Time code reader data Time code generator data User bits reader data User bits generator data Counter display H M S F Display Time code can be shown on the counter display and on the on-screen display during playback and recording. 1 To display time code data on the on-screen display, set the No. 514 menu switch to "TC". ੬ See No. 514 on page 20. 2 To display time code data on the counter display, set the No. 516 menu switch to "TC". ੬ See No. 516 on page 20. 3 Set the [COUNTER] switch to "TC" or "UB". TC: Shows the time code data display. UB: Shows the user bits display. All time code data including time code generator/reader, drop/non-drop frame (U MODEL), CTL interpolation, etc. are shown on the on-screen display HOLD: Start SHIFT: Moves the cursor to the next digit. ADVANCE: Changes the value. PRESET: Enters the set value. MENU ADVANCE PRESET SHIFT SHIFT HOLD SHIFT A. DUB SELECT SET MONITOR OUTPUT COUNTER L CH-1/2 CTL MIX MIX TC R CH-3/4 UB AUDIO TC: Time code UB: User bits CH 1/3 40 30 20 10 CH 2/4 32k 48k SLAVE AUD LOCK SP OVER AUTO OFF DEW 0 dB OVER SERVO RF PB NDF HOLD MENU H M S F Time code/user bits display Preset To give you more control over your material in editing and recording, you can specify a preset time code value while referring to the counter display indications. Determine the required time code value beforehand. • Set the [COUNTER] switch to "TC" so that the counter display shows the time code. • Set the [COUNTER] switch to "UB" to show the user bits on the counter display. Time code presetting is described below. The same procedure is used to preset the user bits, except that user bit values are hexadecimal (0 to F ). 26 27