JVC BR-DV600UA 45 pg user manual for BR-DV600U/E VTR (1130KB) - Page 22

For servicing → See the service manual page 1-16 "1.7 WARNIGN CODES". 12 TROUBLESHOOTING 12-1 Warning indicators If the unit malfunctions during operation, the built-in self-diagnostics system identifies the problem and displays a warning message on the monitor and/or the counter display. Also, the [AUTO OFF] indicator may be shown on the LCD. In this case, turn the power off and then on again to restore operation. If the [AUTO OFF] indicator appears again, the VCR may require repair or adjustment. Consult your local JVC dealer. The VCR's built-in microprocessor is susceptible to interference from externally generated noise or electro-magnetism. In this case, turn the main power (AC and DC power supplies) off, turn on again and check the operation. On-screen display Counter display Error contents Operation Solution CONDENSATION ON DRUM The [DEW] indicator lights. Condensation on the drum. FAILURE LOADING ERR3200 Tape cannot be loaded. FAILURE UNLOADING ERR3300 CASSETTE EJECT FAILURE ERR4100 HOUSING FAILURE ERR4200 TAPE DEFECTIVE ERR5605 • Tape cannot be unloaded. • Tape is jammed. The eject operation is abnormal. The cassette housing is abnormal. The tape ends. TAPE DEFECTIVE ERR5607 The tape is slack. END LEADER DETECTION ERR5702 The tape end sensor is abnormal. BEGIN LEADER DETECTION ERR5802 DRUM MOTOR FAILURE ERR7001 The tape beginning sensor is abnormal. The drum rotation stops. CAP MOTOR FAILURE ERR7101 The capstan rotation stops. • When a cassette is not loaded, the drum starts to rotate. • When a cassette is loaded, the AUTO OFF mode is engaged and the operation stops. Operation stops. No operations are possible. Wait for the drum to stop rotating, then load a cassette. Do not use the unit until the AUTO OFF mode is disengaged. Turn the power on again. In some cases, the tape may be damaged, so use a different tape. If the problem persists, consult your JVC dealer. 40 12 TROUBLESHOOTING On-screen display Counter display Error contents Operation Solution SUP REEL FAILURE The supply reel rotation is abnormal. ERR7202~ 7203 TAKE UP REEL FAILURE ERR7302~ 7303 SYSCON REF ERROR ERR8400 PC TAPE INHIBIT Pc7APE LP INHIBIT LPiNh REC INHIBIT REciNh The takeup reel rotation is abnormal. System controller reference signal failure. A data tape for personal computer is used. A tape recorded in the LP mode is played back. The cassette's safety slide is set to "SAVE". Copy-guarded signals are input. Operation stops. No operations are possible. Operation stops. No operations are possible. Operation continues. Operation stops. Operation stops. Turn the power on again. In some cases, the tape may be damaged, so use a different tape. If the problem persists, consult your JVC dealer. Turn the power on again. Use a tape on which NTSC (U MODEL), PAL (E MODEL) signals are recorded. Use a tape recorded in the SP mode. Set the safety slide to "REC". Copy-guarded signals cannot be recorded. 1394 INHIBIT 1394iNh EE CHECK INHIBIT EEiNh No signal is input to the [DV IN/OUT] connector. Copy-guarded signals are input. When the IEEE 1394 input is selected, the EE check is performed. Operation stops. Operation continues. Input signals to the [DV IN/ OUT] connector. Copy-guarded signals cannot be recorded. When the IEEE 1394 input is selected, the EE check cannot be performed. AUDIO DUB INHIBIT ADBiNh The cassette's safety slide is set to "SAVE". The tape was recorded with the 48 kHz sampling rate. The No. 245 menu switch is set to "48K". Audio dubbing was attempted on a tape recorded in the LP mode. Operation stops. Set the safety slide to "REC". Use a tape recorded at the 32 kHz sampling rate. Set the No. 245 menu switch to "32K". Audio dubbing cannot be performed on tapes recorded in the LP mode. SSF INHIBIT SSFiNh FAN MOTOR FAILURE FAN STOP SSF data error occurs. The fan motor stops. Operation continues. Use a tape on which SSF data has been properly recorded. Operation stops about 60 seconds after the fan motor stops (with the No. 397 menu switch set to "ENABLE"). Consult your nearest JVC dealer. HEAD CLOG HEAD CLOG The video head is clogged. The operation continues. Clean with a dedicated head cleaning tape. Refer to the separate enclosure, "Notes on the use of a cleaning tape". 41