JVC BR-DV600UA 45 pg user manual for BR-DV600U/E VTR (1130KB) - Page 16

9 TIME CODE H M S F H M S F H M S F H M S F H M S F 1 Set the menu switches. (੬ See page 20.) 5 Set the No. 414 menu switch to "PRESET". 5 Set the No. 415 menu switch. Setting is not necessary for user bits. REC RUN: The time code is counted only during recording. FREE RUN: The time code is counted after the preset is complete. 5 Set the No. 416 menu switch. Setting is not necessary for user bits. NON DROP : Engages the Non-Drop Frame mode. DROP : Engages the Drop Frame mode. (U MODEL) 2 Press the [HOLD] button to engage the time code setting mode. [The uppermost digit blinks. 3 Press the [ADVANCE] button to change the value. [The blinking number increases. • Hold down the [SHIFT] button and press the [ADVANCE] button to reset all digits to "0". 4 Press the [SHIFT] button to change the digit. [The blinking cursor on the digit moves to the right. 5 3 4 To change the digit, repeat steps to . 6 Press the [PRESET] button to enter the value. [The time code setting mode is released and the normal display is restored. 7 To check the preset time code, press the [REC] button in the Stop mode. 28 9 TIME CODE CH-1/3 REC LEVEL VIDEO CASSETTE RECORDER BR-DV600U OPERATE ON/OFF EJECT CH-2/4 MENU ADVANCE PRESET SHIFT SHIFT HOLD SHIFT A. DUB PHONES SELECT SET MONITOR OUTPUT COUNTER L CH-1/2 CTL MIX MIX TC R CH-3/4 UB AUDIO CH 1/3 40 30 20 10 CH 2/4 32k 48k SLAVE AUD LOCK SP OVER AUTO OFF DEW 0 dB OVER SERVO RF PB NDF HOLD MENU H M S F REC PLAY PAUSE REMOTE REW STOP FF LOCAL MIC [COUNTER] switch [REC] button [STOP] button [PLAY] button Recording Time code can be recorded in the following ways. 5 Time code recording starts from the preset data. 5 Time code recording follows the time code already recorded on the tape. 5 Time code recording starts from the preset data. Menu switch setting No. 414 "PRESET" No. 415 "REC RUN" or "FREE RUN" No. 416 "NON DROP" or "DROP" (U MODEL) Operation 1 Check the preset value. Set the [COUNTER] switch to "TC" or "UB". In the Stop mode, press the [REC] button. [Time code data is shown on the on-screen display and counter display. On the on-screen display, the counter mode is shown as "TCG" or "UBG". Release your finger from the [REC] button to restore the previous display. 2 Start recording. While pressing the [REC] button, press the [PLAY] button. [Time code and user bits are recorded. To stop recording, press the [STOP] button. Playback Operation 1 Select the time code data to be displayed. Set the [COUNTER] switch to "TC" or "UB". [The counter display shows the time code or user bits. 2 Press the [PLAY] button to play back the time code and user bits. LTC time code is output from the rear panel's [TIME CODE OUT] connector. VITC time code is not output. The time code data is shown on the on-screen display and counter display. On the on-screen display, the counter mode is shown as "TCR" or "UBR". To stop playback, press the [STOP] button. 5 Time code recording follows the time code already recorded on the tape. Menu switch setting No. 414 "REGEN" No. 415 "REC RUN" or "FREE RUN" No. 416 "NON DROP" or "DROP" (U MODEL) Operation 1 Start recording. While pressing the [REC] button, press the [PLAY] button. [The time code and user bits are recorded following the data recorded on the tape. The time code data is shown on the on-screen display and counter display. On the on-screen display, the counter mode is shown as "TCR" or "UBR". To stop recording, press the [STOP] button. Reference Playback time code Time code data is recorded in the sub code area of the tape. During playback, the data in the sub code area is processed in the LTC time code format and output to the [TIME CODE OUT] connector. Note on time code playback without user bits 5 When you play back a tape that has no user bits recorded (for example, a tape recorded on a consumer MiniDV VCR), the user bits that were played back last will be displayed. 29