JVC HR-XVS44U Supplementary Material - Page 74

Connecting To A Dolby Digital Decoder, or An Amplifier With A Built-in DTS

Get JVC HR-XVS44U PDF manuals and user guides View all JVC HR-XVS44U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

74 EN REMOTE (cont.) Connecting To A Dolby Digital Decoder or An Amplifier With A Built-in DTS (DVD deck only) These instructions enable you to connect your unit to dolby digital decoder or amplifier with a built-in DTS. DIGITAL AUDIO OUT To DIGITAL AUDIO input Dolby Digital decoder or amplifier with a built-in DTS Back of unit Optical cable (not supplied) Note for connection: Remove the connector cover from the unit and remove the protection cap from the cable. Make connections. Connect the optical cable between the unit and the Dolby Digital decoder or amplifier with a built-in DTS. NOTES: ● For Dolby digital sound, set "DIGITAL AUDIO OUTPUT" to "DOLBY DIGITAL/PCM". (੬ pg. 81) ● For DTS sound, set "DIGITAL AUDIO OUTPUT" to "STREAM/ PCM". (੬ pg. 81) CAUTIONS: ● This unit has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them. ● Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
74
EN
REMOTE (cont.)
Connecting To A Dolby Digital Decoder
or An Amplifier With A Built-in DTS
(DVD deck only)
These instructions enable you to connect your unit to dolby digital decoder or amplifier with a built-in DTS.
Make connections.
Connect the optical cable between the unit and the
Dolby Digital decoder or amplifier with a built-in DTS.
NOTES:
●
For Dolby digital sound, set “DIGITAL AUDIO OUTPUT” to
“DOLBY DIGITAL/PCM”. (
±
pg. 81)
●
For DTS sound, set “DIGITAL AUDIO OUTPUT” to “STREAM/
PCM”. (
±
pg. 81)
CAUTIONS:
●
This unit has a dynamic range of more than 80 dB with regards
to its Hi-Fi audio capability. It is recommended that you check
the maximum level if you are going to listen to the Hi-Fi audio
signals through a stereo amplifier. A sudden surge in the input
level to the speakers may damage them.
●
Some speakers and televisions are specially shielded to
prevent television interference. If both are of the non-shielded
type, do not place the speakers adjacent to the TV set as this
can adversely affect the video playback picture.
Back of unit
Note for connection:
Remove the connector cover from the
unit and remove the protection cap from
the cable.
Optical cable
(not supplied)
Dolby Digital decoder or
amplifier with a built-in DTS
DIGITAL AUDIO OUT
To DIGITAL AUDIO
input