JVC HR-XVS44U Supplementary Material - Page 88

Timer Recording Vcr Deck

Get JVC HR-XVS44U PDF manuals and user guides View all JVC HR-XVS44U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

88 EN TROUBLESHOOTING (cont.) TIMER RECORDING (VCR deck) SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. Timer recording won't work. ● The clock and/or the timer have been set Re-perform the clock and/or timer incorrectly. settings. ● The timer is not engaged. Press TIMER and confirm that "#" is displayed on the front display panel. 2. Timer programing is not possible. ● Timer recording is in progress. Timer programing can't be performed while a timer recording is in progress. Wait until it finishes. 3. "#" on the front display panel won't stop blinking. 4 and "$" on the front display panel won't stop blinking. ● The timer is engaged but there's no cassette loaded. ● The loaded cassette has had its record safety tab removed. Load a cassette with the record safety tab intact. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact. ● The end of the tape was reached during timer recording. The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program. 5. "#" blinks for 10 seconds and the Timer mode is disengaged. 6. "⅜" and "$" on the front display panel won't stop blinking. 7. "N", "⅜" and "$" on the front display panel won't stop blinking. ● TIMER has been pressed when there are no programs in memory, or the timer record information has been programed incorrectly. ● The end of the tape was reached during Instant Timer Recording. ● The loaded cassette has had its record safety tab removed. Check the programed data and reprogram as necessary, then press TIMER again. The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact. ● The end of the tape was reached during Satellite Auto Recording. The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
88
EN
TROUBLESHOOTING (cont.)
TIMER RECORDING (VCR deck)
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1.
Timer recording won’t work.
●
The clock and/or the timer have been set
incorrectly.
Re-perform the clock and/or timer
settings.
●
The timer is not engaged.
Press
TIMER
and confirm that “
#
” is
displayed on the front display panel.
2.
Timer programing is not possible.
●
Timer recording is in progress.
Timer programing can’t be performed
while a timer recording is in progress.
Wait until it finishes.
3. “
#
” on the front display panel won’t
stop blinking.
●
The timer is engaged but there’s no
cassette loaded.
Load a cassette with the record safety tab
intact.
4. “
#
”, “
²
” and “
$
” on the front
display panel won’t stop blinking.
●
The loaded cassette has had its record
safety tab removed.
Remove the cassette and cover the hole
with adhesive tape, or insert a cassette
with the record safety tab intact.
●
The end of the tape was reached during
timer recording.
The program may not have been recorded
in its entirety. Next time make sure you
have enough time on the tape to record
the entire program.
5. “
#
” blinks for 10 seconds and the
Timer mode is disengaged.
●
TIMER
has been pressed when there are
no programs in memory, or the timer
record information has been programed
incorrectly.
Check the programed data and re-
program as necessary, then press
TIMER
again.
6. “
²
” and “
$
” on the front display
panel won’t stop blinking.
●
The end of the tape was reached during
Instant Timer Recording.
The program may not have been recorded
in its entirety. Next time make sure you
have enough time on the tape to record
the entire program.
7. “
N
”, “
²
” and “
$
” on the front display
panel won’t stop blinking.
●
The loaded cassette has had its record
safety tab removed.
Remove the cassette and cover the hole
with adhesive tape, or insert a cassette
with the record safety tab intact.
●
The end of the tape was reached during
Satellite Auto Recording.
The program may not have been recorded
in its entirety. Next time make sure you
have enough time on the tape to record
the entire program.