JVC LT-32E478 Instructions - Page 40

Tuner Setup, Auto Tuner Setup

Get JVC LT-32E478 - 32inch LCD TV PDF manuals and user guides
UPC - 046838028946
View all JVC LT-32E478 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Tuner Setup Auto Tuner Setup The auto tuner setup function is described on page 23 as the interactive plug-in menu. If you need to run the auto tuner setup again, follow the steps below. Press the MENU button - + Tuner Setup > Auto Tuner Setup π† √® π† √® √® π† √® † To "Tuner Setup" To enter Tuner Mode Scan Mode To "Auto Tuner Setup" To enter To choose "Cable" or "Air" To "Scan Mode" To choose "Auto", "STD", "HRC" or "IRC" Select Operate To "Start" Press the OK button (Programming will take serveral minutes) Air Auto Start BACK Back MENU Exit The auto tuner is finished when the message "Programming Over !" appears onscreen. Notes: • When the Tuner Mode is set to "Cable", it is possible to select "Scan Mode" • If no channels were found using Auto Tuner Setup, check your antenna cable and the settings for Tuner Mode/Scan Mode. • You can also access the "Front Menu" screen by using the MENU button on the side of the TV instead of the remote control. It has "Video Status", "Aspect", "Auto Tuner Setup" and "Menu". Choose "Auto Tuner Setup" by pressing MENU† on the side panel and enter by using the CHANNEL +/- buttons ( √ OPERATE ® ). 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
40
Auto Tuner Setup
The auto tuner setup function is described on page 23 as the interactive plug-in menu.
If you
need to run the auto tuner setup again, follow the steps below.
Press the M
ENU
button
π
†
To "Tuner Setup"
√
®
To enter
π
†
To "Auto Tuner Setup"
√
®
To enter
√
®
To choose "Cable" or "Air"
π
†
To "Scan Mode"
√
®
To choose "Auto", "STD", "HRC" or "IRC"
†
To "Start"
Press the O
K
button (Programming will take serveral minutes)
The auto tuner is finished when the message
"Programming Over !"
appears onscreen.
Tuner Setup > Auto Tuner Setup
Tuner Mode
Scan Mode
Select
BACK
Back
MENU
Exit
Air
Auto
Operate
–
+
Start
Notes:
•
When the Tuner Mode is set to "Cable", it is possible to select "Scan Mode"
•
If no channels were found using Auto Tuner Setup, check your antenna cable and the
settings for Tuner Mode/Scan Mode.
•
You can also access the "Front Menu" screen by using the M
ENU
button on the side of the
TV instead of the remote control.
It has "Video Status", "Aspect", "Auto Tuner Setup" and
"Menu".
Choose "Auto Tuner Setup" by pressing M
ENU
†
on the side panel and enter by
using the C
HANNEL
+/- buttons (
√
OPERATE
®
).
Tuner Setup