Konica Minolta bizhub C360 bizhub C220/C280/C360 PKI Security Operations User - Page 37

FAX function

Get Konica Minolta bizhub C360 PDF manuals and user guides View all Konica Minolta bizhub C360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

bizhub C360/C280/C220 for PKI Card System Security Function Security Function Ver. 1.02 Jul. 2010 13. FAX function 13. FAX function NOTE • When the user use the machine with the facsimile function, it is necessary to install and setting the optional FAX kit properly by the service engineer. 13.1 Installing/setting procedure of the FAX kit 13.1.1 Install procedure 1. Turn off the machine and unplug the power cord from the power outlet. 2. Remove the mounting bracket from the PCI expansion board (four screws). 3. Remove the cover from the back of the machine as shown in the illustration (four screws). 4. Remove the plate as shown below (12 screws). 5. Remove the hard disk and its mounting bracket together from the machine (two screws). 6. Disconnect the two connectors from the hard disk. 7. Mount the PCI expansion board on the hard disk mounting bracket (four screws removed in step 2). 8. Connect the two connectors removed in step 6 to the hard disk. 9. Connect the PCI expansion board connector to the machine and screw the mounting bracket (two screws removed in step 5). 10. Reinstall the plate that has been removed in step 4 (12 screws). 11. Reinstall the cover that has been removed in step 3 (four screws). 12. Remove the cover from the right side of the machine as shown in the illustration (four screws). 13. If the machine does not have the paper feed cabinet installed, remove the indicated knockout using nippers. 14. Remove the left shield cover (six screws). 15. Check to make sure that SW2 on the FAX control board is set to "LINE-1." 16. Insert the FAX kit into the left socket and tighten the two shoulder screws. 17. Reinstall the cover removed in step 12 (four screws). 18. Open the door of the cover installed in step 17. 19. Connect the modular cable. 20. Route the modular cable as shown in the illustration below. 21. Close the door of the cover. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
Security Function Ver. 1.02 Jul. 2010
13. FAX function
33
bizhub C360/C280/C220
for PKI Card System
Security Function
13.
FAX function
NOTE
•
When the user use the machine with the facsimile function, it is necessary to
install and setting the optional FAX kit properly by the service engineer.
13.1
Installing/setting procedure of the FAX kit
13.1.1
Install procedure
1.
Turn off the machine and unplug the power cord from the power outlet.
2.
Remove the mounting bracket from the PCI expansion board (four screws).
3.
Remove the cover from the back of the machine as shown in the illustration (four
screws).
4.
Remove the plate as shown below (12 screws).
5.
Remove the hard disk and its mounting bracket together from the machine (two
screws).
6.
Disconnect the two connectors from the hard disk.
7.
Mount the PCI expansion board on the hard disk mounting bracket (four screws
removed in step 2).
8.
Connect the two connectors removed in step 6 to the hard disk.
9.
Connect the PCI expansion board connector to the machine and screw the mounting
bracket (two screws removed in step 5).
10.
Reinstall the plate that has been removed in step 4 (12 screws).
11.
Reinstall the cover that has been removed in step 3 (four screws).
12.
Remove the cover from the right side of the machine as shown in the illustration (four
screws).
13.
If the machine does not have the paper feed cabinet installed, remove the indicated
knockout using nippers.
14.
Remove the left shield cover (six screws).
15.
Check to make sure that SW2 on the FAX control board is set to “LINE-1.”
16.
Insert the FAX kit into the left socket and tighten the two shoulder screws.
17.
Reinstall the cover removed in step 12 (four screws).
18.
Open the door of the cover installed in step 17.
19.
Connect the modular cable.
20.
Route the modular cable as shown in the illustration below.
21.
Close the door of the cover.