Kyocera TASKalfa 180 Operation Guide - Page 37

Loading Originals, Placing Originals on the Platen, Important, Caution

Get Kyocera TASKalfa 180 PDF manuals and user guides View all Kyocera TASKalfa 180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Preparations Loading Originals Follow the steps below to load originals for copying or sending. Placing Originals on the Platen You may place books or magazines on the platen in addition to ordinary sheet originals. In addiiton, When copying from an original which cannot be set in the document processor, open the document processor and set the original directly on the platen. 1 Open the original cover. Note 2 If the optional document processor is installed, open the document processor. Before opening the document processor, be sure that there are no originals left on the original table or on the original eject table. Originals left on the original table or on the original eject table may fall off when the document processor is opened. Keep the document processor open if the original is 40 mm or thicker. Place the original. Put the scanning side facedown and align it flush against the original size indicator plates with the back left corner as the reference point. 3 Close the original cover. Important! Do not push the original cover forcefully when you close it. Excessive pressure may crack the platen glass. Note Shadows may be produced around the edges and in the middle of open-faced originals. Caution Do not leave the document processor open as there is a danger of personal injury. 2-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Preparations
2-10
Loading Originals
Follow the steps below to load originals for copying or sending.
Placing Originals on the Platen
You may place books or magazines on the platen in addition to ordinary sheet originals. In addiiton,
When copying from an original which cannot be set in the document processor, open the document
processor and set the original directly on the platen.
1
Open the original cover.
Note
If the optional document processor is installed, open the document processor. Before opening the
document processor, be sure that there are no originals left on the original table or on the original
eject table. Originals left on the original table or on the original eject table may fall off when the
document processor is opened.
2
Keep the document processor open if the original is 40 mm or thicker.
Place the original. Put the scanning side facedown
and align it flush against the original size indicator
plates with the back left corner as the reference point.
3
Close the original cover.
Important!
Do not push the original cover forcefully when you close it. Excessive pressure may crack the platen
glass.
Note
Shadows may be produced around the edges and in the middle of open-faced originals.
Caution
Do not leave the document processor open as there is a danger of personal injury.