Kyocera TASKalfa 180 Operation Guide - Page 39

How to Load Originals, to Auto Selection Mode.

Get Kyocera TASKalfa 180 PDF manuals and user guides View all Kyocera TASKalfa 180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Preparations How to Load Originals Before loading originals, be sure that there are no originals left on the original eject table. Originals left on the original eject table may cause the new originals to jam. 1 Adjust the original width guides to fit the originals. Note Before setting originals, make sure that there are no originals remaining on the original eject table. Originals left on the eject table may cause other originals to jam. When setting multiple originals at one time, be sure to use originals of the same size. It is, possible, however to use different size originals of the same width (for example, 11 x 17" (Ledger) and 11 x 8 1/2" or A4 and A3 at the same time in the auto selection mode. Refer to Chapter 4 Auto Selection Mode.) 2 Arrange the originals in order and set them face up (front side up for 2-sided originals) on the original table. Important! Be sure to set only a number of originals that does not exceed the level indicator located inside the rear original insert guide. If you set originals exceeding the specified number, the originals may jam. 2-12 To keep ejected originals from falling off the machine, open the ejection extension when using large originals such as A3, B4, 11 × 17" (Ledger), and 8 1/2 × 14" (Legal). When copying from 2-sided originals, the originals are temporarily ejected onto the ejection tray in order to turn them over. Do not touch them at this point. Any attempt to remove them may cause the originals to jam

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Preparations
2-12
How to Load Originals
Before loading originals, be sure that there are no originals left on the original eject table. Originals
left on the original eject table may cause the new originals to jam.
1
Adjust the original width guides to fit the originals.
Note
Before setting originals, make sure that there are no
originals remaining on the original eject table. Originals
left on the eject table may cause other originals to jam.
When setting multiple originals at one time, be sure to
use originals of the same size. It is, possible, however
to use different size originals of the same width (for
example, 11 x 17" (Ledger) and 11 x 8
1/2
" or A4 and
A3 at the same time in the auto selection mode. Refer
to Chapter 4 Auto Selection Mode.)
2
Arrange the originals in order and set them face up
(front side up for 2-sided originals) on the original table.
Important!
Be sure to set only a number of originals that does not
exceed the level indicator located inside the rear
original insert guide. If you set originals exceeding the
specified number, the originals may jam.
To keep ejected originals from falling off the machine,
open the ejection extension when using large originals
such as A3, B4, 11 × 17" (Ledger), and 8
1/2
× 14"
(Legal).
When copying from 2-sided originals, the originals are
temporarily ejected onto the ejection tray in order to
turn them over. Do not touch them at this point. Any
attempt to remove them may cause the originals to jam