LG 37LD325H Owners Manual - Page 140

FTG Mode of Operation, FTG Configuration Overview

Get LG 37LD325H PDF manuals and user guides View all LG 37LD325H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

FTG Mode of Operation FTG Configuration Overview The following steps outline local FTG configuration of individual TVs. Since these models are equipped with the EBL module, they can also be broadcast configured in FTG Mode by a Free-To-Guest Management Appliance (FMA) head end device. Refer to the Free-To-Guest (FTG) Configuration Application manual and/or the Installation & Setup manual for the FMA device for further information. Note: FTG Configuration Application software is available online at: www.LGcommercial.com/ FTGsoftware. 1. Install (if necessary) and launch the FTG Configuration Application (v5.0.0 or higher) on the PC that will be used to configure the EBL. 2. Build a Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration Utility (or, if applicable, open an existing FTG Configuration (.rml) file). 3. Connect the PC to the TV-LINK CFG jack on the rear connections panel using a USB-to-TTL serial cable (TTL-232R-5V-AJ). If necessary, install the device driver on the PC. 4. Turn ON the TV. Note: The TV will briefly display a green text banner that shows the EBL firmware version and release date. 5. "Write" the FTG Channel Map to the EBL (converts EBL from Pass-through Mode to FTG Mode). 6. "Read" the current FTG Installer Menu settings from the EBL using the FTG Installer Menu Configuration Utility. If necessary to make changes to Installer Menu items, "Write" them back to the EBL in FTG Mode. 7. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for future use. 8. Tune the TV to a Logical Channel in the FTG Channel Map. RESET UPDATE HDMI 2 .......... HDMI /DVI IN 1 .......... RJP RGB IN (PC) SPEAKER OUT (8 ) REMOTE CONTROL OUT AUDIO IN (RGB/DVI) RS-232C IN (SERVICE ONLY) ......... AV IN 1 VIDEO L/MONO-AUDIO-R ANTENNA IN GAME CONTROL TV-LINK CFG Y PB PR VIDEO L R AUDIO COMPONENT IN (26LD320H only) (26LD320H only: GAME CONTROL/MPI) USB-to-TTL Serial Cable Required for local FTG configuration. TV-LINK CFG Use for local FTG configuration. Laptop PC 206-4163 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
23
206-4163
FTG Mode of Operation
FTG Configuration Overview
Laptop
PC
UPDATE
RESET
AUDIO IN
(RGB/DVI)
RS-232C IN
(SERVICE ONLY)
.....
....
..........
2
1
HDMI
/DVI IN
RJP
VIDEO
L/MONO
-AUD
IO-
R
AV IN 1
RGB IN (PC)
.....
.....
.....
TV-LINK
CFG
GAME
CONTROL
..........
REMOTE
CONTROL
OUT
SPEAKER
OUT
8
HDMI
COMPONENT IN
R
L
P
B
Y
P
R
VIDEO
AUDIO
(
)
ANTENNA IN
The following steps outline local FTG configuration of individual TVs. Since these models are equipped
with the EBL module, they can also be broadcast configured in FTG Mode by a Free-To-Guest
Management Appliance (FMA) head end device. Refer to the
Free-To-Guest (FTG) Configuration
Application
manual and/or the Installation & Setup manual for the FMA device for further information.
Note:
FTG Configuration Application software is available online at: www.LGcommercial.com/
FTGsoftware.
1. Install (if necessary) and launch the FTG Configuration Application (v5.0.0 or higher) on the PC that
will be used to configure the EBL.
2. Build a Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration
Utility (or, if applicable, open an existing FTG Configuration (.rml) file).
3. Connect the PC to the TV-LINK CFG jack on the rear connections panel using a USB-to-TTL serial
cable (TTL-232R-5V-AJ). If necessary, install the device driver on the PC.
4. Turn ON the TV. Note: The TV will briefly display a green text banner that shows the EBL firmware
version and release date.
5. “Write” the FTG Channel Map to the EBL (converts EBL from Pass-through Mode to FTG Mode).
6. “Read” the current FTG Installer Menu settings from the EBL using the FTG Installer Menu
Configuration Utility. If necessary to make changes to Installer Menu items, “Write” them back to the
EBL in FTG Mode.
7. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for
future use.
8. Tune the TV to a Logical Channel in the FTG Channel Map.
TV-LINK CFG
Use for local FTG
configuration.
USB-to-TTL
Serial Cable
Required for local
FTG configuration.
(26LD320H only)
(26LD320H only:
GAME CONTROL/MPI)