LG 37LD325H Owners Manual - Page 191

port, THE CLONE HAS CONTROL OF THE TV message will appear on, different Master TV Setups.

Get LG 37LD325H PDF manuals and user guides View all LG 37LD325H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 191 highlights

Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs, as this will damage the clone programmer and the PPV card. Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure). LT2002 Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 23 before beginning any cloning procedures. • A slow flashing green light indicates that there are communication problems between the TV and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles. • If the status indicator is red, the LT2002 batteries are low and should be replaced. Install four (4) high-quality alkaline AA batteries. • Learning and Teaching is only possible between identical model TVs; however, the LT2002 clone programmer can store up to three different Master TV Setups. Antenna or CATV THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION XX THE TV IS VERSION XX THE SW IS REViSION XX CLONE CLOCK = XX:XX TV CLOCK = XX:XX - PRESS ANY KEY TO CONTINUE MPI Cable Ferrite Core (TDK, ZCAT 2035-0930) $POOFDUDBCMFUP 57.1*+BDLBOE GPMMPXPOTDSFFO instructions Status *OEJDBUPS MPI $PMPS Reset tHSFFO CBUUFSZPL tSFE CBUUFSZMPX #MJOLQBUUFSO tTMPX QPXFSPO no communications tIFBSUCFBUQPXFSPO communications ok LT2002 Clone Programmer ® QuickSet II Programmer LT2002 ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA Learn Setup from Master TV 1. Ensure the Master TV is set up completely and in Pass-through Mode. 2. If an analog channel is not available, direct tune the TV to an Aux source, or select an Aux source, such as AV-1, from the Input Menu. Then, plug one end of the MPI cable into the TV MPI port. 3. If there is a good connection after the LT2002 is connected to the TV MPI port, "THE CLONE HAS CONTROL OF THE TV" message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu. 4. Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press ENTER to proceed to the Memory Bank Selection Menu (see sample screen on next page). 5. Select the clone Memory Bank in which to store the Master Setup by pressing either Channel key repeatedly to choose Memory Bank 1, 2, or 3. Note: If you choose a Memory Bank that already has a Master device's setup programmed into it, that setup will be overwritten by the new Master TV Setup. (Continued on next page) THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION XX THE TV IS VERSION XX THE SW IS REVISION XX CLONE CLOCK = XX:XX TV CLOCK = XX:XX - PRESS ANY KEY TO CONTINUE. - DISCONNECT CLONE WHEN DONE. CLONE SELECTION MENU (1) LEARN FROM TV (2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP - TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS. - TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER. 206-4177 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
27
206-4177
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION
XX
THE TV IS VERSION
XX
THE SW IS REVISION
XX
CLONE CLOCK
=
XX:XX
TV
CLOCK
=
XX:XX
- PRESS ANY KEY TO CONTINUE.
- DISCONNECT CLONE WHEN DONE.
CLONE SELECTION MENU
(1)
LEARN FROM TV
(2)
TEACH TO TV
(3)
SET CLONE CLOCK FROM TV
(4)
SET TV CLOCK FROM CLONE
(5)
DISPLAY TV SETUP
(6)
DISPLAY CLONE SETUP
-
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
Learn Setup from Master TV
1. Ensure the Master TV is set up completely and in Pass-through Mode.
2. If an analog channel is not available, direct tune the TV to an Aux source,
or select an Aux source, such as AV-1, from the Input Menu. Then, plug one
end of the MPI cable into the TV MPI port.
3. If there is a good connection after the LT2002 is connected to the TV MPI
port, “THE CLONE HAS CONTROL OF THE TV” message will appear on
the TV screen. Press any key on the Installer Remote to access the LT2002
Clone Selection Menu.
4. Press
1
on the Installer Remote to select
LEARN FROM TV
from the Clone
Selection Menu; then press
ENTER
to proceed to the Memory Bank Selec-
tion Menu (see sample screen on next page).
5. Select the clone Memory Bank in which to store the Master Setup by press-
ing either Channel key repeatedly to choose Memory Bank 1, 2, or 3. Note:
If you choose a Memory Bank that already has a Master device’s setup pro-
grammed into it, that setup will be overwritten by the new Master TV Setup.
Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer
LT2002 Cloning Notes
• Read the IMPORTANT CLONING
INFORMATION on page 23 before
beginning any cloning procedures.
• A slow flashing green light indicates
that there are communication
problems between the TV and the
LT2002 clone programmer. If this is
the case, check for a damaged
cable, poor contacts, or other
connection troubles.
• If the status indicator is red, the
LT2002 batteries are low and
should be replaced. Install four (4)
high-quality alkaline AA batteries.
• Learning and Teaching is only
possible between identical model
TVs; however, the LT2002 clone
programmer can store up to three
different Master TV Setups.
Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target
TVs, as this will damage the clone programmer and the PPV card.
Ferrite Core
(TDK, ZCAT
2035-0930)
Antenna
or CATV
QuickSet II Programmer
LT2002
®
ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA
communications ok
no communications
Reset
Status
instructions
MPI
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION
XX
THE TV IS VERSION
XX
THE SW IS REViSION
XX
CLONE CLOCK
=
XX:XX
TV
CLOCK
=
XX:XX
- PRESS ANY KEY TO CONTINUE
MPI
Cable
LT2002 Clone
Programmer
(Continued on next page)
Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).