LG ARUN096BT2 Installation Manual - Page 74

Procedure

Get LG ARUN096BT2 PDF manuals and user guides View all LG ARUN096BT2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Test Run manifold Liquid Pipe Gas Pipe Capillary Assembly Procedure 1. Arrange manifold,capillary assembly, refrigerant vessel and scale 2. Connect manifold to the gas pipe service valve of ODU as shown in the figure. 3. Connect manifold and Capillary tube. Use designated capillary assembly only. If designated capillary assembly isn't used, the system may get damaged. 4. Connect capillary and refrigerant vessel. 5. Purge hose and manifold. 6. After Is displayed, open the valve and charge the refrigerant s Error contents about auto refrigerant charging function 1. : Temperature Range Error (In case that IDU or ODU is out of range) 2. : Low Pressure Descent Error (In case the system runs at low pressure limit for over 10 minutes) 3. : Judging rapid refrigerant inflow ( In case the liquid refrigerant flows in because of not using desig- nated Capillary Assembly) 4. : Instability Error( In case the high/low pressure target doesn't get satisfied for some time after the starting operation) CAUTION 1. Guaranteed temperature range (Error will occur if temperature is out of range) IDU : 20°C(68°F) ~ 32°C(90°F) ODU : 0°C(32°F) ~ 43°C (77°F) 2. For refrigerant charging, use designated device only. (Capillary Assem Set) 3. Set the IDU wired remote controller temperature sensing mode as IDU 4. Be careful that IDU should not be thermo off. 74 Outdoor Unit

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
74
Outdoor Unit
Test Run
Procedure
1. Arrange manifold,capillary assembly, refrigerant vessel and scale
2. Connect manifold to the gas pipe service valve of ODU as shown in the figure.
3. Connect manifold and Capillary tube.
Use designated capillary assembly only.
If designated capillary assembly isn't used, the system may get damaged.
4. Connect capillary and refrigerant vessel.
5. Purge hose and manifold.
6. After
Is displayed, open the valve and charge the refrigerant
Liquid Pipe
Gas Pipe
manifold
Capillary Assembly
■
Error contents about auto refrigerant charging function
1.
: Temperature Range Error (In case that IDU or ODU is out of range)
2.
: Low Pressure Descent Error (In case the system runs at low pressure limit for over 10 minutes)
3.
: Judging rapid refrigerant inflow ( In case the liquid refrigerant flows in because of not using desig-
nated Capillary Assembly)
4.
: Instability Error( In case the high/low pressure target doesn't get satisfied for some time
after the starting operation)
CAUTION
1. Guaranteed temperature range (Error will occur if temperature is out of range)
IDU :
20°C(68°F) ~ 32°C(90°F)
ODU : 0°C(32°F)
~ 43°C (77°F)
2. For refrigerant charging, use designated device only. (Capillary Assem Set)
3. Set the IDU wired remote controller temperature sensing mode as IDU
4. Be careful that IDU should not be thermo off.