LG LUWD1CW Owners Manual - Page 44

Error Codes

Get LG LUWD1CW PDF manuals and user guides View all LG LUWD1CW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

44 TROUBLESHOOTING Error Codes Problem Possible Cause Water supply faucets are not fully open. Water line hoses are kinked, pinched, or crushed. Water inlet filters are clogged. Water supply pressure to faucet or house is too low. Water supply connected with leak-limiting hoses. Drain hose is kinked, pinched, or clogged. If the balance is not successful, this error will be displayed. The load is too small. Heavy articles are mixed with lighter items. The load is out of balance. Drawer is not closed properly. Solutions ••Make sure that the water faucets are fully open. ••Make sure that the hoses are not kinked or pinched. Be careful when moving the washer. ••Clean the inlet filters. See Maintenance in the Care and Cleaning section. ••Check another faucet in the house to make sure that household water pressure is adequate and flow is not restricted. Disconnect the inlet hose from the washer and run a few gallons of water through the hose to flush the water supply lines. If flow is too low, contact a plumber to have the water lines repaired. ••Hoses designed to limit leaks can trip falsely and prevent the washer from filling. The use of leak limiting hoses is not recommended. ••Make sure the drain hose is free of clogs or kinks and is not pinched behind or under the washer. ••The automatic attempt to rebalance the load was not successful. The cycle has been paused to allow the load to be manually adjusted. ••Small loads may need additional items to be added to allow the washer to balance the load. ••The load may have heavy items loaded with lighter items. Always try to wash articles of somewhat similar weight to allow the washer to evenly distribute the weight of the load for spinning. ••Manually redistribute the load if articles have become tangled preventing the automatic rebalancing from working properly. ••Close the drawer and press Start/Pause button to start the cycle. ••If the drawer is closed and the error message is displayed, call for service.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
44
TROUBLESHOOTING
Error Codes
Problem
Possible Cause
Solutions
Water supply faucets are not
fully open.
•
Make sure that the water faucets are fully open.
Water line hoses are kinked,
pinched, or crushed.
•
Make sure that the hoses are not kinked or pinched. Be
careful when moving the washer.
Water inlet filters are clogged.
•
Clean the inlet filters. See Maintenance in the Care and
Cleaning section.
Water supply pressure to
faucet or house is too low.
•
Check another faucet in the house to make
sure that
household water pressure is adequate and flow is not
restricted. Disconnect the inlet hose from the washer
and run a few gallons of water through the hose to
flush the water supply lines. If flow is too low, contact a
plumber to have the water lines repaired.
Water supply connected with
leak-limiting hoses.
•
Hoses designed to limit leaks can trip falsely and
prevent the washer from filling. The use of leak limiting
hoses is not recommended.
Drain hose is kinked, pinched,
or clogged.
•
Make sure the drain hose is free of clogs or kinks and is
not pinched behind or under the washer.
If the balance is not
successful, this error will be
displayed.
•
The automatic attempt to rebalance the load was not
successful. The cycle has been paused to allow the
load to be manually adjusted.
The load is too small.
•
Small loads may need additional items to be added to
allow the washer to balance the load.
Heavy articles are mixed with
lighter items.
•
The load may have heavy items loaded with lighter
items. Always try to wash articles of somewhat similar
weight to allow the washer to evenly distribute the
weight of the load for spinning.
The load is out of balance.
•
Manually redistribute the load if articles have become
tangled preventing the automatic rebalancing from
working properly.
Drawer is not closed properly.
•
Close the drawer and press
Start/Pause
button to start
the cycle.
•
If the drawer is closed and the error message is
displayed, call for service.