Lenovo ThinkPad T410 Hardware Maintenance Manual - Page 56

Beep symptoms, LCD-related symptoms, Table 4. Beep symptoms - indicator lights

Get Lenovo ThinkPad T410 PDF manuals and user guides View all Lenovo ThinkPad T410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Beep symptoms Table 4. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. Reseat the LCD connector. 2. LCD assembly. 3. External CRT. 4. System board. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See "Numeric error codes" on page 44. Two short beeps and a blank screen. 1. System board. 2. DIMM. Two or more beeps, or a continuous beep. Operating system starts successfully. If a mini-PCI Ethernet card is installed, confirm that Alert On LAN 2 in BIOS Setup Utility is disabled. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2. System board One short beep, pause, three short beeps, pause, three more short beeps, and one short beep. Only the cursor appears. Reinstall the operating system. Four cycles of four short beeps and a blank screen. System board (security chip) Five short beeps and a blank screen. System board No-beep symptoms Table 5. No-beep symptoms Symptom or error No beep, power-on indicator on, LCD blank, and no POST. No beep, power-on indicator on, and LCD blank during POST. The power-on password prompt appears. The hard-disk password prompt appears. FRU or action, in sequence 1. Make sure that every connector is connected tightly and correctly. 2. DIMM. 3. System board. 1. Reseat DIMM. 2. System board. A power-on password or a supervisor password is set. Type the password and press Enter. A hard-disk password is set. Type the password and press Enter. LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced. Notes: • This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later. 50 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Beep symptoms
Table 4. Beep symptoms
Symptom or error
FRU or action, in sequence
One beep and a blank, unreadable, or flashing LCD.
1.
Reseat the LCD connector
.
2. LCD assembly.
3. External CRT.
4. System board.
One long and two short beeps, and a blank or unreadable
LCD.
1.
System board
.
2. LCD assembly.
3. DIMM.
Two short beeps with error codes.
POST error. See “Numeric error codes” on page 44.
Two short beeps and a blank screen.
1.
System board
.
2. DIMM.
Two or more beeps, or a continuous beep. Operating
system starts successfully.
If a mini-PCI Ethernet card is installed, confirm that
Alert
On LAN 2
in BIOS Setup Utility is
disabled
.
Three short beeps, pause, three more short beeps, and
one short beep.
One short beep, pause, three short beeps, pause, three
more short beeps, and one short beep.
1.
DIMM
.
2. System board
Only the cursor appears.
Reinstall the operating system
.
Four cycles of four short beeps and a blank screen.
System board
(security chip)
Five short beeps and a blank screen.
System board
No-beep symptoms
Table 5. No-beep symptoms
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, LCD blank, and no
POST.
1.
Make sure that every connector is connected
tightly and correctly
.
2. DIMM.
3. System board.
No beep, power-on indicator on, and LCD blank during
POST.
1.
Reseat DIMM
.
2. System board.
The power-on password prompt appears.
A power-on password or a supervisor password is set.
Type the password and press
Enter
.
The hard-disk password prompt appears.
A hard-disk password is set. Type the password and
press
Enter
.
LCD-related symptoms
Important:
The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a
small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but
excessive pixel problems can cause viewing concerns.
If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the
LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
Notes:
• This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later.
50
Hardware Maintenance Manual