Lenovo ThinkPad W530 Hardware Maintenance Manual - Page 32

Strategy for replacing a hard disk drive, a solid state drive, o - user manual

Get Lenovo ThinkPad W530 PDF manuals and user guides View all Lenovo ThinkPad W530 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Strategy for replacing a hard disk drive, a solid state drive, or an mSATA solid state drive Always try to run a low-level format operation before replacing a hard disk drive or a solid state drive. This will cause all customer data on the hard disk drive or solid state drive to be lost. Be sure that the customer has a current backup of the data before you perform this task. Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten. If the computer is shipped with an mSATA solid state drive and a hard disk drive, the mSATA solid state drive is used only for the "cache" function and the Intel Rapid Start Technology. Users are not recommended to replace the mSATA solid state drive by themselves. Otherwise, the "cache" function will not work and the Intel Rapid Start Technology cannot be used any more. Important notice for replacing a system board Some components mounted on a system board are very sensitive. Improper handling of a system board can cause damage to those components, and may cause a system malfunction. Attention: When handling a system board: • Do not drop a system board or apply any excessive force to it. • Avoid rough handling of any kind. • Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset. How to use error codes Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed, begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU Index for the computer you are servicing. Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), and eSupport will load these products as the 4-digit MT and 3-digit model, where model = "CTO" (example: 1829-CTO). Custom Model Variant (CMV) This is a unique configuration that has been negotiated between Lenovo and the customer. A unique 4-digit MT and 3-digit model is provided to the customer to place orders (example: 1829-W15). A CMV is a special bid offering. Therefore, it is not generally announced. • The MTM portion of the machine label is the 4-digit MT and 3-digit model, where model = "CTO" (example: 1829-CTO). The PRODUCT ID portion of the machine label is the 4-digit MT and 3-digit CMV model (example: 1829-W15). • The PEW record is the 4-digit MT and 3-digit model, where model = "CTO" (example: 1829-CTO). 26 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Strategy for replacing a hard disk drive, a solid state drive, or an mSATA
solid state drive
Always try to run a low-level format operation before replacing a hard disk drive or a solid state drive. This
will cause all customer data on the hard disk drive or solid state drive to be lost. Be sure that the customer
has a current backup of the data before you perform this task.
Attention:
The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect
drive, data or programs can be overwritten.
If the computer is shipped with an mSATA solid state drive and a hard disk drive, the mSATA solid state drive
is used only for the “cache” function and the Intel Rapid Start Technology. Users are not recommended to
replace the mSATA solid state drive by themselves. Otherwise, the “cache” function will not work and the
Intel Rapid Start Technology cannot be used any more.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper handling of a system board can
cause damage to those components, and may cause a system malfunction.
Attention:
When handling a system board:
•
Do not drop a system board or apply any excessive force to it.
•
Avoid rough handling of any kind.
•
Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.
How to use error codes
Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed,
begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error
codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU
Index for the computer you are servicing.
Strategy for replacing FRUs for CTO, CMV, and GAV
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this
configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label,
Product Entitlement Warehouse (PEW), and eSupport will load these products as the 4-digit MT and 3-digit
model, where model = “CTO” (example: 1829-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between Lenovo and the customer. A unique 4-digit
MT and 3-digit model is provided to the customer to place orders (example: 1829-W15). A CMV is a special
bid offering. Therefore, it is not generally announced.
•
The MTM portion of the machine label is the 4-digit MT and 3-digit model, where model = “CTO”
(example: 1829-CTO). The PRODUCT ID portion of the machine label is the 4-digit MT and 3-digit CMV
model (example: 1829-W15).
•
The PEW record is the 4-digit MT and 3-digit model, where model = “CTO” (example: 1829-CTO).
26
Hardware Maintenance Manual