Linksys SPA921 Cisco Small Business IP Phone SPA9X1 Administration Guide - Page 119

SDP Payload Types, exactly 1 RR Receiver Report; the last SR carries no RR. The SDES contains CNAME

Get Linksys SPA921 - Cisco - IP Phone PDF manuals and user guides
UPC - 745883570799
View all Linksys SPA921 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

SIP Tab Field RTCP Tx Interval (not applicable to SPA901) No UDP Checksum (not applicable to SPA901) Symmetric RTP (not applicable to SPA901) Stats In BYE (not applicable to SPA901) Chapter 5 Linksys IP Phone Field Reference Description Interval for sending out RTCP sender reports on an active connection. It can range from 0 to 255 seconds. During an active connection, the Linksys IP phone can be programmed to send out compound RTCP packet on the connection. Each compound RTP packet except the last one contains a SR (Sender Report) and a SDES (Source Description). The last RTCP packet contains an additional BYE packet. Each SR except the last one contains exactly 1 RR (Receiver Report); the last SR carries no RR. The SDES contains CNAME, NAME, and TOOL identifiers. The CNAME is set to @, NAME is set to (or Anonymous if user blocks caller ID), and TOOL is set to the Vendor/Hardware-platform-software-version (such as Linksys/Linksys IP phone-1.0.31(b)). The NTP timestamp used in the SR is a snapshot of the Linksys IP phone's local time, not the time reported by an NTP server. If the Linksys IP phone receives a RR from the peer, it attempts to compute the round trip delay and show it as the value (ms) in the Info section of Linksys IP phone web page. Defaults to 0. Select yes if you want the Linksys IP phone to calculate the UDP header checksum for SIP messages. Otherwise, select no. Defaults to no. Enable symmetric RTP operation. If enabled, sends RTP packets to the source address and port of the last received valid inbound RTP packet. If disabled (or before the first RTP packet arrives) sends RTP to the destination as indicated in the inbound SDP. Defaults to yes. Determines whether the Linksys IP phone includes the P-RTP-Stat header or response to a BYE message. The header contains the RTP statistics of the current call. Select yes or no from the drop-down menu. The format of the P-RTP-Stat header is: P-RTP-State: PS=,OS=,PR=,OR=,PL=,JI=,LA=,DU=,EN=,DE=. Defaults to no. SDP Payload Types The configured dynamic payloads are used for outbound calls only where the Linksys IP phone presents the SDP offer. For inbound calls with a SDP offer, the Linksys IP phone follow the caller dynamic payload type assignments. The Linksys IP phone uses the configured codec names in its outbound SDP. The Linksys IP phone ignores the codec names in incoming SDP for standard payload types (0 - 95). For dynamic payload types, the Linksys IP phone identifies the codec by the configured codec names. Comparison is case-insensitive. Field AVT Dynamic Payload Description AVT dynamic payload type. Ranges from 96-127. Defaults to 101. 5-14 Linksys IP Phone Administrator Guide Firmware Version 5.1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
5-14
Linksys IP Phone Administrator Guide
Firmware Version 5.1
Chapter 5
Linksys IP Phone Field Reference
SIP Tab
SDP Payload Types
The configured dynamic payloads are used for outbound calls only where the Linksys IP phone presents
the SDP offer. For inbound calls with a SDP offer, the Linksys IP phone follow the caller dynamic
payload type assignments.
The Linksys IP phone uses the configured codec names in its outbound SDP. The Linksys IP phone
ignores the codec names in incoming SDP for standard payload types (0 – 95). For dynamic payload
types, the Linksys IP phone identifies the codec by the configured codec names. Comparison is
case-insensitive.
RTCP Tx Interval
(not applicable to SPA901)
Interval for sending out RTCP sender reports on an active connection. It can range from
0 to 255 seconds. During an active connection, the Linksys IP phone can be programmed
to send out compound RTCP packet on the connection. Each compound RTP packet
except the last one contains a SR (Sender Report) and a SDES (Source Description). The
last RTCP packet contains an additional BYE packet. Each SR except the last one contains
exactly 1 RR (Receiver Report); the last SR carries no RR. The SDES contains CNAME,
NAME, and TOOL identifiers. The CNAME is set to <User ID>@<Proxy>, NAME is set
to <Display Name> (or Anonymous if user blocks caller ID), and TOOL is set to the
Vendor/Hardware-platform-software-version (such as Linksys/Linksys IP
phone-1.0.31(b)). The NTP timestamp used in the SR is a snapshot of the Linksys IP
phone’s local time, not the time reported by an NTP server. If the Linksys IP phone
receives a RR from the peer, it attempts to compute the round trip delay and show it as the
<Call Round Trip Delay> value (ms) in the Info section of Linksys IP phone web page.
Defaults to 0.
No UDP Checksum
(not applicable to SPA901)
Select yes if you want the Linksys IP phone to calculate the UDP header checksum for
SIP messages. Otherwise, select no.
Defaults to no.
Symmetric RTP
(not applicable to SPA901)
Enable symmetric RTP operation. If enabled, sends RTP packets to the source address and
port of the last received valid inbound RTP packet. If disabled (or before the first RTP
packet arrives) sends RTP to the destination as indicated in the inbound SDP.
Defaults to yes.
Stats In BYE
(not applicable to SPA901)
Determines whether the Linksys IP phone includes the P-RTP-Stat header or response to
a BYE message. The header contains the RTP statistics of the current call. Select yes or
no from the drop-down menu. The format of the P-RTP-Stat header is:
P-RTP-State: PS=<packets sent>,OS=<octets sent>,PR=<packets received>,OR=<octets
received>,PL=<packets lost>,JI=<jitter in ms>,LA=<delay in ms>,DU=<call duration in
s>,EN=<encoder>,DE=<decoder>.
Defaults to no.
Field
Description
Field
Description
AVT Dynamic Payload
AVT dynamic payload type. Ranges from 96-127.
Defaults to 101.