Netgear EN516 EN516 Installation Guide - Page 21

hub or repeater.

Get Netgear EN516 - Hub - EN PDF manuals and user guides View all Netgear EN516 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Installation Guide for the Model EN516 Ethernet Hub Port 16 is switchable between Normal (MDI-X) and Uplink (MDI) positions and should be configured according to the following guidelines: • Set the Normal/Uplink push button to the Normal position and use a straight-through cable if the remote end of the cable is connected to an MDI-wired device such as a PC. • Set the Normal/Uplink push button to the Uplink position and use a straight-through cable if the remote end of the cable is connected to an MDI-X device such as a 10 Mbps or 100 Mbps hub or repeater. For further cabling guidelines, refer to Appendix B, "Cabling Specifications." Refer to the following illustrations for connecting to the RJ-45 ports and proceed to "Completing and Verifying the Installation" on page 3-11. Figure 3-2 illustrates a workstation connected to an RJ-45 port on the Model EN516 hub. 12 Key: 1 = Network adapter card with RJ-45 connector 2 = UTP cable to Model EN516 hub Power Data Collision 1 Link RX 9 Link RX 8 Normal/Uplink 16 34FA Figure 3-2. Connecting a workstation to an RJ-45 port on the Model EN516 hub Note: Ethernet specifications limit segments to 328 feet (100 m) in length. Installation 3-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
Installation Guide for the Model EN516 Ethernet Hub
Installation
3-5
Port 16 is switchable between Normal (MDI-X) and Uplink (MDI) positions and should be
configured according to the following guidelines:
•
Set the Normal/Uplink push button to the Normal position and use a straight-through cable if
the remote end of the cable is connected to an MDI-wired device such as a PC.
•
Set the Normal/Uplink push button to the Uplink position and use a straight-through cable if
the remote end of the cable is connected to an MDI-X device such as a 10 Mbps or 100 Mbps
hub or repeater.
For further cabling guidelines, refer to Appendix B, “Cabling Specifications.”
Refer to the following illustrations for connecting to the RJ-45 ports and proceed to “Completing
and Verifying the Installation” on page 3-11.
Figure 3-2 illustrates a workstation connected to an RJ-45 port on the Model EN516 hub.
Key:
1 = Network adapter card with RJ-45 connector
2 = UTP cable to Model EN516 hub
Figure 3-2.
Connecting a workstation to an RJ-45 port on the Model EN516 hub
Note:
Ethernet specifications limit segments to 328 feet (100 m) in length.
34FA
Normal/Uplink
16
8
Link
RX
Link
RX
9
1
Power
Data
Collision
2
1