Netgear GS748TP-100NAS GS724TP User Manual - Page 17

Network without a DHCP Server, Manually Assigning Network Parameters

Get Netgear GS748TP-100NAS PDF manuals and user guides View all Netgear GS748TP-100NAS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

GS700TP Smart Switch Software Administration Manual Network without a DHCP Server This section describes how to set up your switch in a network without a DHCP server, and is divided into the following tasks: • Manually assign network parameters for your switch • Configure the NIC settings on the host PC • Log in to the web-based switch management utility Manually Assigning Network Parameters If your network has no DHCP service, you must assign a static IP address to your switch. You can also assign the switch a static IP address even if your network has DHCP service. Proceed as follows: 1. Connect the GS700TP Gigabit PoE Smart Switch to your existing network. 2. Power on the switch by plugging in the AC-DC power adapter. The default IP is 192.168.0.239. 3. Install the SmartWizard Discovery utility on your computer. The SmartWizard Discovery utility is located on the switch installation CD. 4. Start the SmartWizard Discovery utility. 5. Click Discover for the SmartWizard Discovery utility to find your GS700TP Gigabit PoE Smart Switch. You should see a screen similar to that shown in Figure 1-1. 6. Click Configuration Setting. A screen similar to that shown below appears. Getting Started with Switch Management 1-5 v1.0, December 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
GS700TP Smart Switch Software Administration Manual
Getting Started with Switch Management
1-5
v1.0, December 2007
Network without a DHCP Server
This section describes how to set up your switch in a network without a DHCP server, and is
divided into the following tasks:
•
Manually assign network parameters for your switch
•
Configure the NIC settings on the host PC
•
Log in to the web-based switch management utility
Manually Assigning Network Parameters
If your network has no DHCP service, you must assign a static IP address to your switch. You can
also assign the switch a static IP address even if your network has DHCP service. Proceed as
follows:
1.
Connect the GS700TP Gigabit PoE Smart Switch to your existing network.
2.
Power on the switch by plugging in the AC-DC power adapter. The default IP is
192.168.0.239.
3.
Install the SmartWizard Discovery utility on your computer. The SmartWizard Discovery
utility is located on the switch installation CD.
4.
Start the SmartWizard Discovery utility.
5.
Click
Discover
for the SmartWizard Discovery utility to find your GS700TP Gigabit PoE
Smart Switch. You should see a screen similar to that shown in Figure 1-1.
6.
Click
Configuration Setting
. A screen similar to that shown below appears.