Nokia IP350 Installation Guide - Page 33

To perform the initial configuration, Nokia Contact Information - reset

Get Nokia IP350 - Security Appliance PDF manuals and user guides View all Nokia IP350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Using a Console Connection to Perform the Initial Configuration 2. Connect the other end of the cable to the VT100 console or to a system running a terminal-emulation program. To perform the initial configuration 1. Turn on the appliance. At the console a series of startup messages appears, then the following prompt appears: BOOTMGR[0]> The prompt remains on the screen for about five seconds. Note For information about using the boot manager, see Chapter 7, "Using the Boot Manager." After some miscellaneous output appears, the following prompt appears: Hostname? If the Hostname? prompt does not appear on the console, check the console port and console display connections to ensure that the serial cable is completely plugged in at both ends. If you verify the console connections and still do not see either the BOOTMGR> or Hostname? prompts, verify that the terminal or terminal emulator program settings are correct. If the settings are correct, contact your Nokia service provider as listed in "Nokia Contact Information" on page 3. 2. Respond to the Hostname? prompt within 30 seconds to prevent the DHCP client from starting. If the DHCP client starts, it might configure the appliance with an incorrect host name and IP address (this could happen if a DHCP server on your network is configured to respond to any request). To reset the incorrect host name and IP address: a. Establish a console connection to the system. b. Enter the following: Nokia 60s and 100s Installation Guide 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Using a Console Connection to Perform the Initial Configuration
Nokia 60s and 100s Installation Guide
33
2.
Connect the other end of the cable to the VT100 console or to a system
running a terminal-emulation program.
To perform the initial configuration
1.
Turn on the appliance.
At the console a series of startup messages appears, then the following
prompt appears:
BOOTMGR[0]>
The prompt remains on the screen for about five seconds.
Note
For information about using the boot manager, see
Chapter 7, “Using
the Boot Manager.”
After some miscellaneous output appears, the following prompt appears:
Hostname?
If the
Hostname?
prompt does not appear on the console, check the
console port and console display connections to ensure that the serial
cable is completely plugged in at both ends. If you verify the console
connections and still do not see either the
BOOTMGR>
or
Hostname?
prompts, verify that the terminal or terminal emulator program settings
are correct. If the settings are correct, contact your Nokia service provider
as listed in
“Nokia Contact Information”
on page 3.
2.
Respond to the
Hostname?
prompt within 30 seconds to prevent the
DHCP client from starting.
If the DHCP client starts, it might configure the appliance with an
incorrect host name and IP address (this could happen if a DHCP server
on your network is configured to respond to any request). To reset the
incorrect host name and IP address:
a.
Establish a console connection to the system.
b.
Enter the following: