Nokia IP350 Installation Guide - Page 68

Make sure that all four standoff connections are properly aligned., To secure the connections

Get Nokia IP350 - Security Appliance PDF manuals and user guides View all Nokia IP350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

6 Installing and Replacing Other Components 7. Place the screws through the standoff holes on the card and into the standoffs on the motherboard. Screw Accelerator card Standoff hole Motherboard standoff 8. Turn each screw clockwise so that the card is attached to the standoffs. Do not tighten completely. 9. Make sure that all four standoff connections are properly aligned. 10. To secure the connections, tighten the screws firmly, but do not overtighten. 11. Slide the chassis assembly back into the appliance and resecure the two thumbscrews. 60s 00487 Chassis assembly thumbscrews Reseating the chassis assembly automatically restores power to the appliance. 12. Configure your software to use hardware acceleration. For more information, see "" on page 69. 68 Nokia 60s and 100s Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
6
Installing and Replacing Other Components
68
Nokia 60s and 100s Installation Guide
7.
Place the screws through the standoff holes on the card and into the
standoffs on the motherboard.
8.
Turn each screw clockwise so that the card is attached to the standoffs.
Do not tighten completely.
9.
Make sure that all four standoff connections are properly aligned.
10.
To secure the connections, tighten the screws firmly, but do not
overtighten.
11.
Slide the chassis assembly back into the appliance and resecure the two
thumbscrews.
Reseating the chassis assembly automatically restores power to the
appliance.
12.
Configure your software to use hardware acceleration. For more
information, see
“”
on page 69.
Screw
Accelerator card
Standoff hole
Motherboard standoff
00487
60s
Chassis assembly thumbscrews