Nokia IP380 Installation Guide - Page 100

Upgrading the Boot Manager

Get Nokia IP380 - Security Appliance PDF manuals and user guides View all Nokia IP380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

8 Using the Boot Manager To install the new boot manager 1. Start the appliance in single-user mode. 2. At the IPSO command prompt, enter: /etc/install_bootmgr wd0 /image/current/bootmgr/ nkipflash The command installs the new boot manager image (nkipflash) into the flash device (wd0). The installation takes some time to complete. Do not interrupt the installation process. Upgrading the Boot Manager The command to upgrade your boot manager has the following syntax: upgrade_bootmgr boot-device boot-file where boot-device is the storage device from which the boot manager loads at boot up and boot-file is the new boot manager image. The new boot manager options are cpipflash, cpvpnflash, nkipflash, and nkvpnflash. Execute the upgrade_bootmgr command from IPSO (the operating system), not from the boot manager. For complete upgrade procedures, refer to the appropriate version of release notes. Note To install the new boot manager, you must be in single user mode. To upgrade the boot manager 1. Get the upgraded boot manager image from the appropriate Nokia customer support site as listed in the Nokia Contact Information section at the front of this guide. 2. Start the IP300 Series appliance in single-user mode. 92 Nokia IP300 Series Security Platform Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
8
Using the Boot Manager
92
Nokia IP300 Series Security Platform Installation Guide
To install the new boot manager
1.
Start the appliance in single-user mode.
2.
At the IPSO command prompt, enter:
/etc/install_bootmgr wd0 /image/current/bootmgr/
nkipflash
The command installs the new boot manager image (
nkipflash
) into the
flash device (
wd0
). The installation takes some time to complete. Do not
interrupt the installation process.
Upgrading the Boot Manager
The command to upgrade your boot manager has the following syntax:
upgrade_bootmgr
boot-device boot-file
where
boot-device
is the storage device from which the boot manager loads at
boot up and
boot-file
is the new boot manager image. The new boot manager
options are
cpipflash
,
cpvpnflash
,
nkipflash
, and
nkvpnflash
. Execute
the
upgrade_bootmgr
command from IPSO (the operating system), not from
the boot manager.
For complete upgrade procedures, refer to the appropriate version of release
notes.
Note
To install the new boot manager, you must be in single user mode.
To upgrade the boot manager
1.
Get the upgraded boot manager image from the appropriate Nokia
customer support site as listed in the Nokia Contact Information section at
the front of this guide.
2.
Start the IP300 Series appliance in single-user mode.