NordicTrack 14.0 Elliptical Uk Manual - Page 36

from the left Crank Arm 20. Set the Left Roller Arm

Get NordicTrack 14.0 Elliptical PDF manuals and user guides View all NordicTrack 14.0 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

HOW TO ADJUST THE REED SWITCH If the console does not display correct feedback, the reed switch should be adjusted. Press the power switch to the off position and unplug the power cord. To adjust the reed switch, first see assembly step 11 on page 10. Remove the Left Roller Arm (12) from the Left Pedal Arm (44). Next, see EXPLODED DRAWING A on page 41 and EXPLODED DRAWING B on page 42. Remove the M8 x 16mm Screw (72), the Axle Cover (53), and the M8 x 25mm Washer (149) from the upper end of the Left Roller Arm (12). Then, remove the Left Roller Arm from the left Crank Arm (20). Set the Left Roller Arm out of the way. See EXPLODED DRAWING C on page 43. Using a flat screwdriver, pry the left Crank Arm Cover (71) off the Left Front Shield (73). Next, locate the Reed Switch (38). Turn the left Crank Arm (20) until one of the Magnets (43) on the Pulley (19) is aligned with the Reed Switch. Loosen, but do not remove, the two M4 x 16mm Screws (104). Slide the Reed Switch (38) slightly closer to or away from the Magnet (43). Then, retighten the Screws. Plug in the power cord and press the power switch to the reset position. Turn the left Crank Arm (20) for a moment. Repeat these actions until the console displays correct feedback. Then, reattach the left crank arm cover and the left roller arm. HOW TO GREASE THE ROLLERS See the EXPLODED DRAWING near the end of this manual. If the Rollers (51) squeak when moving on the Left and Right Tracks (11, 124), apply a small amount of the included PTFE grease to a paper towel. Spread a thin layer of grease evenly along the Left and Right Tracks. Then, wipe off any excess grease. 38 43 104 19 20 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
36
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
Press the power switch to the off position and
unplug the power cord.
To adjust the reed switch, first see assembly step 11
on page 10. Remove the Left Roller Arm (12) from
the Left Pedal Arm (44).
Next, see EXPLODED DRAWING A on page 41 and
EXPLODED DRAWING B on page 42. Remove the
M8 x 16mm Screw (72), the Axle Cover (53), and the
M8 x 25mm Washer (149) from the upper end of the
Left Roller Arm (12). Then, remove the Left Roller Arm
from the left Crank Arm (20). Set the Left Roller Arm
out of the way.
See EXPLODED DRAWING C on page 43. Using a
flat screwdriver, pry the left Crank Arm Cover (71) off
the Left Front Shield (73).
Next, locate the Reed Switch (38). Turn the left Crank
Arm (20) until one of the Magnets (43) on the Pulley
(19) is aligned with the Reed Switch.
Loosen, but do not remove, the two M4 x 16mm
Screws (104). Slide the Reed Switch (38) slightly
closer to or away from the Magnet (43). Then, retighten
the Screws. Plug in the power cord and press the
power switch to the reset position. Turn the left Crank
Arm (20) for a moment.
Repeat these actions until the console displays correct
feedback. Then, reattach the left crank arm cover and
the left roller arm.
HOW TO GREASE THE ROLLERS
See the EXPLODED DRAWING near the end of this
manual. If the Rollers (51) squeak when moving on the
Left and Right Tracks (11, 124), apply a small amount
of the included PTFE grease to a paper towel. Spread
a thin layer of grease evenly along the Left and Right
Tracks. Then, wipe off any excess grease.
43
38
104
19
20