Panasonic PVL751 PVL751 User Guide - Page 21

TV Playback or Viewing, VCR Playback using PlayPak, Connections, CATV System Installer, Remove

Get Panasonic PVL751 - VHS-C CAMCORDER PDF manuals and user guides View all Panasonic PVL751 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Playing Back Recordings TV Playback or Viewing Connect Camcorder to a TV to view playback or recordings in progress. Before you begin... • Connect Camcorder to power source. • Make all TV-Camcorder connections. Connections T V Audio/ Video Out To Audio To Video In In Audio/Video Cable (Supplied) 1 Set POWER to: VCR © view playback. CAMERA © view picture as it is recorded. 2 Turn TV ON and set to LINE INPUT. See TV owner's manual. 3 Begin playback or recording. CATV System Installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Basic Operation VCR Playback using PlayPak 1 Load Battery in PlayPak 2 Insert Cassette in PlayPak Remove Battery lid and insert AA battery. • Do not reverse polarity. • Replace battery when tape loading/unloading takes longer than usual. 3 Remove Cassette a Slide RELEASE and wait for lid to open. b Push cassette out through hole in bottom of PlayPak with your finger. a Turn cassette Tape Wheel in direction of arrow to take up any slack. b Slide RELEASE to open cassette lid. c Insert the cassette with the window up and on the left, then snap lid shut. • Do not obstruct cassette reel while loading. • Allow PlayPak Load Detector to fully retract before using in VHS VCR. Load Detector 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
21
Basic Operation
Playing Back Recordings
Connections
1
Set POWER to:
VCR
view playback.
CAMERA
view picture as it is
recorded.
2
Turn TV ON and set to LINE INPUT.
See TV owner’s manual.
3
Begin playback or recording.
Audio/
Video Out
CATV System Installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40
of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable
entry as practical.
Connect Camcorder to a TV to view
playback or recordings in progress.
Before you begin...
• Connect Camcorder to power source.
• Make all TV-Camcorder connections.
To Video
In
To Audio
In
Audio/Video Cable
(Supplied)
T V
TV Playback or Viewing
Remove Battery lid
and insert AA
battery.
• Do not reverse
polarity.
• Replace battery
when tape loading/unloading takes
longer than usual.
a
Turn
cassette
Tape Wheel in
direction of arrow
to
take up any slack.
b
Slide
RELEASE
to
open cassette lid.
c
Insert the
cassette
with the
window up and on the
left,
then snap lid shut.
Remove
Cassette
Insert
Cassette in PlayPak
a
Slide
RELEASE
and wait for lid to
open.
b
Push cassette
out through
hole in bottom of
PlayPak with
your finger.
• Do not obstruct cassette reel while loading.
• Allow PlayPak Load Detector to fully retract
before
using in VHS VCR.
Load Detector
Load Battery in PlayPak
VCR Playback using PlayPak
1
3
2