Panasonic TH-65PF12EK User Manual - Page 57

Using Network Function

Get Panasonic TH-65PF12EK PDF manuals and user guides View all Panasonic TH-65PF12EK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Using Network Function This unit has a network function to control the network connected display with your computer. Note: To use the network function, set each "Network Setup" setting and make sure to set the "Control I/F Select" to "LAN". (see page 51) When "LAN" is set, power indicator is lit orange when the slot power is turned on, then the power is turned "Off" with remote control (stand-by state) regardless of the "Slot power" setting. (see page 54) Example of Network Connection COMPUTER Less than 10 cm LAN cable (straight) (not supplied) Ferrite core (supplied) LAN AUDIO PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN SLOT3 Display (main unit, rear) Ferrite core (supplied) Less than 10 cm Installing the Ferrite core Open Hub or broadband router Pull back the tabs (in two places) Wind the cable twice Press the cable through and close Notes: • Make sure the broadband router or hub supports 10BASE-T/100BASE-TX. • To connect a device using 100BASE-TX, use "category 5" LAN cable. • Touching the LAN terminal with a statically charged hand (body) may cause damage due to its discharge. Do not touch the LAN terminal or a metal part of the LAN cable. • For instructions on how to connect, consult your network administrator. Command Control Network function of the unit can control the unit in the same way as serial control from a network. Supported commands Commands used in the serial control are supported. (see page 10) Note: Consult your local Panasonic dealer for detail instructions on command usage. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
SLOT3
P
R
/C
R
/R
P
B
/C
B
/B
Y/G
COMPONENT/RGB IN
LAN
AUDIO
57
Using Network Function
This unit has a network function to control the network connected display with your computer.
Note:
To use the network function, set each “Network Setup” setting and make sure to set the “Control I/F Select” to “LAN”.
(see page 51)
When “LAN” is set, power indicator is lit orange when the slot power is turned on, then the power is turned “Off” with
remote control (stand-by state) regardless of the “Slot power” setting.
(see page 54)
Example of Network Connection
Command Control
Display (main unit, rear)
Hub or broadband router
LAN cable
(straight)
(not supplied)
Notes:
• Make sure the broadband router or hub supports 10BASE-T/100BASE-TX.
• To connect a device using 100BASE-TX, use “category 5” LAN cable.
• Touching the LAN terminal with a statically charged hand (body) may cause damage due to its discharge.
Do not touch the LAN terminal or a metal part of the LAN cable.
• For instructions on how to connect, consult your network administrator.
Network function of the unit can control the unit in the same way as serial control from a network.
Supported commands
Commands used in the serial control are supported. (see page 10)
Note:
Consult your local Panasonic dealer for detail instructions on command usage.
COMPUTER
Less
than
10 cm
Less
than
10 cm
Ferrite core
(supplied)
Ferrite core
(supplied)
Installing the Ferrite core
Pull back the tabs
(in two places)
Wind the cable
twice
Open
Press the cable
through and close