Pioneer DEH-P6200BT Owner's Manual - Page 19
Initial Settings, Operating this unit - update
UPC - 884938103145
View all Pioneer DEH-P6200BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
Operating this unit Section 02 English You can adjust the currently selected equalizer curve setting as desired. Adjusted equalizer curve settings are stored in Custom1 or Custom2. ! A separate Custom1 curve can be created for each source. If you make adjustments when a curve other than Custom2 is selected, the equalizer curve settings will be stored in Custom1. ! A Custom2 curve that is common for all sources can be created. If you make adjustments when the Custom2 curve is selected, the Custom2 curve will be updated. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between equalizer band and level. 3 Press M.C. to switch to equalizer band and then turn M.C. to select. 100Hz-315Hz-1.25kHz-3.15kHz-8kHz 4 Press M.C. to switch to level and then turn M.C. to adjust. Adjustment range: +6 to -6 Loudness (loudness) Loudness compensates for deficiencies in the lowand high-frequency ranges at low volume. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. OFF (off)-Low (low)-Mid (mid)-High (high) 3 Press M.C. to confirm the selection. SW setting 1 (subwoofer on/off setting) This unit is equipped with a subwoofer output which can be turned on or off. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. Normal (normal phase)-Reverse (reverse phase)-OFF (subwoofer off) 3 Press M.C. to confirm the selection. SW setting 2 (subwoofer adjustment) The cut-off frequency and output level can be adjusted when the subwoofer output is on. Only frequencies lower than those in the selected range are outputted from the subwoofer. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between cut-off frequency and output level of subwoofer. 3 Press M.C. to switch to cut-off frequency and then turn M.C. to select cut-off frequency. 50Hz-63Hz-80Hz-100Hz-125Hz 4 Press M.C. to switch to output level and then turn M.C. to adjust output level. Adjustment range: +6 to -24 HPF setting (high pass filter adjustment) When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are output from the front or rear speakers. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the cut-off frequency. OFF (off)-50Hz-63Hz-80Hz-100Hz-125Hz 3 Press M.C. to confirm the selection. Bass booster (bass boost) 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the level. Adjustment range: 0 to +6 3 Press M.C. to confirm the selection. SLA (source level adjustment) SLA (Source Level Adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. ! When selecting FM as the source, you cannot switch to SLA. ! Settings are based on the FM volume level, which remains unchanged. Before adjusting source levels, compare the FM volume level with the level of the source you wish to adjust. ! The AM volume level can also be adjusted with this function. 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume. Adjustment range: +4 to -4 3 Press M.C. to confirm the selection. Note Operation is complete even if the menu is cancelled before being confirmed. Initial Settings 1 Press SRC/OFF and hold until the unit turns off. 2 Press M.C. and hold until the initial setting menu appears in the display. En 19