Pioneer DVJ 1000 Owner's Manual - Page 51
Troubleshooting - servicing
UPC - 012562821481
View all Pioneer DVJ 1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 51 highlights
Other (Troubleshooting) Troubleshooting Incorrect operations can be mistaken as malfunctions. If you believe the unit is not operating correctly, consult the chart below. Sometimes incorrect operation may be due to a malfunction in another component. If the problem is not fixed, check the other components used with the player. If the problem still persists, contact your nearest Pioneer authorized service center or dealer for service. Symptom No power. Discs don't eject when the EJECT (0) button is pressed. Probable Diagnosis ¶ Power cord isn't connected. ¶ The eject/stop mode select switch is set to LOCK. Playback doesn't start when a disc is inserted. Playback stops immediately after starting. ¶ Auto cue function is set to ON. ¶ Disc is loaded with label side down. ¶ Disc is fogged or dirty. ¶ The disc has a different region number. DVD-R/DVD-RW discs cannot be ¶ Disc isn't recorded in video format. played. "NOT VIDEO FORMAT" is displayed. Can't play DVD. ¶ NORMAL/DJ switch is set to "DJ". Some DVDs are constructed to prohibit playing in DJ mode. The marks appear. ¶ Operation is prohibited by disc or player. MP3 can't be played. ¶ Format is wrong. Can't search for MP3 files. ¶ You attempted to search (fast forward/reverse) for files in a different folder. Images don't appear on screen. ¶ Output cables are loose or not connected correctly. ¶ Improper operation of television or video mixer, etc. No sound. ¶ Output cables are loose or not connected correctly. ¶ Improper operation of audio mixer. ¶ Connectors or plugs are dirty. ¶ Player is set to pause mode. Sound is distorted or has noise. ¶ Output cables are not connected correctly. Certain discs produce much noise. Playback is interrupted. DVDs and CDs produce different sound volumes. When auto cue function is ON, track search does not end. During playback, back cue doesn't occur when CUE button is pressed. ¶ Connectors or plugs are dirty. ¶ Electromagnetic influence from television. ¶ Disc has large scratches. ¶ Disc is very dirty. ¶ Due to difference in recording formats. ¶ If intervals between tracks is very long, track search takes longer. ¶ If a non-recorded intervals continue for more than 10 seconds, play will not begin unless auto cue function is turned OFF. ¶ No cue point is set. ¶ NORMAL/DJ switch is set to "NORMAL". ¶ With DVD, some discs do not support DJ operations during playback. ¶ When playing MP3, cue point is in another folder. Loop play doesn't start when OUT/ OUT ADJUST button is pressed. Auto cue setting is not retained. All settings cannot be returned to their factory defaults. ¶ No cue point (loop-in point) has been set. ¶ NORMAL/DJ switch is set to "NORMAL". ¶ Cue points and angle, audio settings are different. ¶ With DVD, some discs do not support point DJ operations during playback. ¶ The power was turned off right after settings were made or changed. Remedy ¶ Connect power cord properly. ¶ Set the player to pause mode or cue standby mode then press EJECT (0) button. ¶ Set the eject/stop mode selector switch to UNLOCK then press EJECT (0) button. ¶ Hold the TIME MODE/AUTO CUE button depressed for 1 second or more to turn the auto cue function off. ¶ Reload the disc with label side up. ¶ Clean the disc. ¶ Check the disc for correct region number. If it is not correct, it cannot be played on this unit. ¶ Record disc in video format. ¶ Set NORMAL/DJ switch to "NORMAL". ¶ Perform correct operation. ¶ See section "Playing MP3 files" on page 10. ¶ MP3 searches can be performed only within the same folder. ¶ Connect correctly. ¶ Confirm settings of television or video mixer, etc. ¶ Connect cables correctly. ¶ Check audio mixer's switches and volume settings. ¶ Clean connectors and plugs. ¶ Press PLAY/PAUSE (6) button to begin playback. ¶ Connect cables correctly to audio mixer line input connectors. Do not connect to MIC connector. ¶ Clean connectors and plugs. ¶ Turn off television or move farther away. ¶ Replace disc. ¶ Clean disc. ¶ Not a malfunction. ¶ Hold the TIME MODE/AUTO CUE button depressed for 1 second or more to turn auto cue function OFF. ¶ Set a cue point. ( P.40) ¶ Set NORMAL/DJ switch to "DJ". ¶ Play back a part supporting DJ operations. ¶ Back cue with MP3 can be performed only within the same folder. ¶ Set a loop-in point. ( P.44) ¶ Set NORMAL/DJ switch to "DJ". ¶ Set angle and audio conditions the same. ¶ Play a part supporting DJ operations. ¶ Wait 10 seconds before turning off the unit after changing settings. 51