Pioneer P770MP Owner's Manual - Page 52

Using nonfading output, Using the high pass filter, Adjusting source levels, Audio Adjustments

Get Pioneer P770MP - Premier In-Dash CD/MP3/WMA/WAV Receiver PDF manuals and user guides
UPC - 037459108803
View all Pioneer P770MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Section 11 Audio Adjustments Only frequencies lower than those in the selected range are outputted from the subwoofer. 3 Push Multi-Control up or down to adjust the output level of the subwoofer. Each pushing Multi-Control up or down increases or decreases the level of the subwoofer. +6  6 is displayed as the level is increased or decreased. Using nonfading output When the nonfading output setting is on, the audio signal does not pass through this units low pass filter (for the subwoofer), but is outputted through the RCA output. 1 Use Multi-Control to select nonfading output on/off setting. ON appears in the display. # When the subwoofer controller setting is only Preout :FULL, you can switch to the nonfading output on/off setting. (Refer to page 55.) 2 Press Multi-Control to turn nonfading output on. ON appears in the display. Nonfading output is now on. # To turn nonfading output off, press Multi-Control again. Adjusting nonfading output level When the nonfading output is on, you can adjust the level of nonfading output. 1 Use Multi-Control to select nonfading output setting. 0 appears in the display. 2 Push Multi-Control up or down to adjust the nonfading output level. Each pushing Multi-Control up or down increases or decreases the level of the nonfading output. +6  6 is displayed as the level is increased or decreased. Using the high pass filter When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are outputted from the front or rear speakers. 1 Use Multi-Control to select HPF. HPF appears in the display. 2 Press Multi-Control to turn high pass filter on. 80Hz appears in the display. High pass filter is now on. # To turn high pass filter off, press Multi-Control again. 3 Push Multi-Control left or right to select cut-off frequency. Each pushing Multi-Control left or right selects cut-off frequencies in the following order: 50Hz80Hz125Hz Only frequencies higher than those in the selected range are outputted from the front or rear speakers. Adjusting source levels SLA (source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. 52 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Only frequencies lower than those in the se-
lected range are outputted from the subwoo-
fer.
3
Push Multi-Control up or down to ad-
just the output level of the subwoofer.
Each pushing
Multi-Control
up or down in-
creases or decreases the level of the subwoo-
fer.
+6
±
±
6
is displayed as the level is
increased or decreased.
Using nonfading output
When the nonfading output setting is on, the
audio signal does not pass through this unit
²
s
low pass filter (for the subwoofer), but is out-
putted through the RCA output.
1
Use Multi-Control to select nonfading
output on/off setting.
ON
appears in the display.
#
When the subwoofer controller setting is only
Preout :FULL
, you can switch to the nonfading
output on/off setting. (Refer to page 55.)
2
Press Multi-Control to turn nonfading
output on.
ON
appears in the display. Nonfading output
is now on.
#
To turn nonfading output off, press
Multi-Control
again.
Adjusting nonfading output level
When the nonfading output is on, you can ad-
just the level of nonfading output.
1
Use Multi-Control to select nonfading
output setting.
0
appears in the display.
2
Push Multi-Control up or down to ad-
just the nonfading output level.
Each pushing
Multi-Control
up or down in-
creases or decreases the level of the nonfad-
ing output.
+6
±
±
6
is displayed as the level is
increased or decreased.
Using the high pass filter
When you do not want low sounds from the
subwoofer output frequency range to play
from the front or rear speakers, turn on the
HPF (high pass filter). Only frequencies higher
than those in the selected range are outputted
from the front or rear speakers.
1
Use Multi-Control to select HPF.
HPF
appears in the display.
2
Press Multi-Control to turn high pass fil-
ter on.
80Hz
appears in the display. High pass filter is
now on.
#
To turn high pass filter off, press
Multi-Control
again.
3
Push Multi-Control left or right to select
cut-off frequency.
Each pushing
Multi-Control
left or right se-
lects cut-off frequencies in the following order:
50Hz
µ
80Hz
µ
125Hz
Only frequencies higher than those in the se-
lected range are outputted from the front or
rear speakers.
Adjusting source levels
SLA (source level adjustment) lets you adjust
the volume level of each source to prevent ra-
dical changes in volume when switching be-
tween sources.
Audio Adjustments
En
52
Section
11