ProForm Power Zt8 Treadmill English Manual - Page 31

Unplug The Power Cord.

Get ProForm Power Zt8 Treadmill PDF manuals and user guides View all ProForm Power Zt8 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

SYMPTOM: The walking belt is off-center or slips when walked on a. If the walking belt is off-center, rst remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered. a b. If the walking belt slips when walked on, rst remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b SYMPTOM: The console display has lines running through it a. If lines appear in the console display, see THE SETTINGS MODE on page 26 and adjust the contrast level of the display. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
31
SYMPTOM: The walking belt is off-center or slips
when walked on
a.
If the walking belt is off-center,
rst remove the
key and
UNPLUG THE POWER CORD.
If the
walking belt has shifted to the left,
use the hex
key to turn the left idler roller screw clockwise 1/2
of a turn;
if the walking belt has shifted to the
right,
turn the left idler roller screw counterclock-
wise 1/2 of a turn. Be careful not to overtighten the
walking belt.
Then, plug in the power cord, insert
the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b.
If the walking belt slips when walked on,
rst
remove the key and
UNPLUG THE POWER
CORD.
Using the hex key, turn both idler roller
screws clockwise, 1/4 of a turn. When the walk-
ing belt is correctly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to
7 cm) off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
SYMPTOM: The console display has lines running
through it
a.
If lines appear in the console display, see THE
SETTINGS MODE on page 26 and adjust the con-
trast level of the display.
a
b