Ryobi RY10518 Operator's Manual - Page 13

Filling The Fuel Tank, Adding Bar And Chain Lubricant

Get Ryobi RY10518 PDF manuals and user guides View all Ryobi RY10518 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

OPERATION FILLING THE FUEL TANK See Figure 2. n Clean the surface around the fuel cap to prevent contamination. n Loosen the fuel cap slowly. n Carefully pour the fuel mixture into the tank. Avoid spillage. n Prior to replacing the fuel cap, clean and inspect the o-ring. n Immediately replace the fuel cap and hand tighten. Wipe up any fuel spillage. NOTE: It is normal for the engine to emit smoke during and after the first use. ADDING BAR AND CHAIN LUBRICANT See Figure 3. Use RYOBI Bar and Chain Lubricant. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. Chain saw should use approximately one tank of lubricant per tank of fuel. NOTE: Do not use dirty, used, or otherwise contaminated lubricants. Damage may occur to the oil pump, bar, or chain. n Carefully pour the bar and chain lubricant into the oil tank. n Fill the oil tank every time you fuel the engine. Fig. 2 Fig. 3 Page 13 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Page 13 — English
FILLING THE FUEL TANK
See Figure 2.
Clean the surface around the fuel cap to prevent
contamination.
Loosen the fuel cap slowly.
Carefully pour the fuel mixture into the tank.
Avoid spillage.
Prior to replacing the fuel cap, clean and inspect the
o-ring.
Immediately replace the fuel cap and hand
tighten. Wipe up any fuel spillage.
NOTE:
It is normal for the engine to emit smoke
during and after the first use.
Fig. 2
ADDING BAR AND CHAIN LUBRICANT
See Figure 3.
Use RYOBI Bar and Chain Lubricant. It is designed
for chains and chain oilers, and is formulated to
perform over a wide temperature range with no dilu-
tion required. Chain saw should use approximately
one tank of lubricant per tank of fuel.
NOTE:
Do not use dirty, used, or otherwise con-
taminated lubricants. Damage may occur to the
oil pump, bar, or chain.
Carefully pour the bar and chain lubricant into
the oil tank.
Fill the oil tank every time you fuel the engine.
Fig. 3
OPERATION