Samsung LN40C630 User Manual - Page 27

To connect the Samsung Wirebss LAN Adapter using - internet

Get Samsung LN40C630 PDF manuals and user guides View all Samsung LN40C630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Notice The pbture may appear corrupted or have statb for some channels when the TV i8connected to the Samsung Wireless LAN Adapter, In such a case, establbh a connection using one of the following methods or connect the Samsung Wirebss LAN Adapter using a USB cable in a }lace that is not affected by radio interference Connect using the USB right angle adapter ii _" H L c..-.-.s..... L To connect the Samsung Wirebss LAN Adapter using the USB right angle adapter, follow these steps: 1. Connect the USB right angle adapter to the Samsung Wireless LAN Adapter. 2. Connect the other end of the right angle adapter to the USB I (//DD) port Connect via an extension cable i j i if i To reconnect the Samsung Wireless LAN Adapter using the extension cable, follow these steps: 1. Connect the extension cable to the USB I (HDD} port 2. Connect the extension cable and Samsung Wireless LAN Adapter. 3. Attach the Samsung Wireless LAN Adapter to the back of the TV near the top, using double-sided adhesive tape Network Setup (Sam s ung Auto C onfiguration The Samsung Auto Configuration function lets you connect your Samsung T',7automatically to non-Samsung wirebss APs. If your non-Samsung AP does not support Samsung Auto Configuraton, you must connect using one of the other methods: PBC(WPS), auto configuration, or manual configuration. To use this function, you must set SWL(Samsung Wireless Link) to Off in the TV's on-screen menu. You can check for equipment that supports Samsung Auto Oonfiguration on www.samsung.com. How to set up using Samsung Auto Configuration 1. Place the AP and 7"\/next to each other and turn them on. Because AP booting times vary, you may have to wait approximately two minutes for your AP to boot up. Ensure the LAN cable is connected to the WAN port of the AP during Samsung Auto Configuration. If it is not connected, Samsung Auto Configuration only confirms that the TV is connected to the AP, but does not confirm it is connected to the Internet. 2. After 2 minutes, connect the Samsung Wireless LAN Adapter to the 7",4When the Samsung Wireless LAN Adapter establishes a connection with your 7"\/,a pop-up window appears 3. As soon as a connection is established, place the AP parallel to the Samsung Wireless LAN Adapter and not farther than than 9 and 7/88 inches (25cm) from it. 4. VVaituntil the connection is automatically established. If Samsung Auto Configuration does not connect your TV to your AP, a pop-up window appears on the screen notifying you of the failure If you want to try using Samsung Auto Configuration again, reset the AP, disconnect the Samsung Wireless LAN Adapter and then try again from Step 1 You can also choose one of the other connection setup methods PBC (WPS), auto, or manual 5. Place the AP in a desired location If the AP settings change or you install a new AP, you must perform the Samsung Auto Configuration procedure again, beginning from Step 1 English 2?

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
Notice
The pbture may appear corrupted or have statb for some
channels when the TV i8connected to the Samsung Wireless
LAN Adapter, In such a case, establbh a connection using one
of the following methods or connect the Samsung Wirebss LAN
Adapter using a USB cable in a }lace that is not affected by
radio interference
Connect using the USB right angle adapter
H
ii _"
L
................................
".c--s
L
To connect the Samsung Wirebss LAN Adapter using the
USB right angle adapter, follow these steps:
1.
Connect the USB right angle adapter to the Samsung
Wireless LAN Adapter.
2.
Connect the other end of the right angle adapter to the
USB I (//DD) port
Connect via an extension cable
i
j
i
if
i
To reconnect the Samsung Wireless LAN Adapter using the
extension cable, follow these steps:
1.
Connect the extension cable to the USB I (HDD} port
2.
Connect the extension cable and Samsung Wireless LAN
Adapter.
3.
Attach the Samsung Wireless LAN Adapter to the back of
the TV near the top, using double-sided adhesive tape
Network
Setup
(Sam s ung Auto
C onfiguration)
........................................
The Samsung Auto Configuration function lets you connect
your Samsung T',7automatically to non-Samsung wirebss
APs. If your non-Samsung AP does not support Samsung
Auto Configuraton, you must connect using one of the
other methods: PBC(WPS),
auto configuration, or manual
configuration.
To use this function, you must set SWL(Samsung
Wireless
Link) to Off in the TV's on-screen menu.
You can check for equipment
that supports
Samsung
Auto Oonfiguration on www.samsung.com.
How to set up using Samsung
Auto Configuration
1.
Place the AP and 7"\/next to each other and turn them on.
Because AP booting times vary, you may have to wait
approximately two minutes for your AP to boot up.
Ensure the LAN cable is connected to the WAN
port of the AP during Samsung Auto Configuration.
If it is not connected, Samsung Auto Configuration
only confirms that the TV is connected to the AP,
but does not confirm it is connected to the Internet.
2.
After 2 minutes, connect the Samsung Wireless LAN
Adapter to the 7",4When the Samsung Wireless LAN
Adapter establishes a connection with your 7"\/,a pop-up
window appears
3.
As soon as a connection is established, place the AP
parallel to the Samsung Wireless LAN Adapter and not
farther than than 9 and 7/88 inches (25cm) from it.
4.
VVaituntil the connection is automatically established.
If Samsung Auto Configuration does not connect
your TV to your AP, a pop-up
window appears on
the screen notifying you of the failure
If you want
to try using Samsung Auto Configuration
again,
reset the AP, disconnect
the Samsung Wireless
LAN Adapter and then try again from Step 1 You
can also choose one of the other connection
setup methods
PBC (WPS), auto, or manual
5.
Place the AP in a desired location
If the AP settings change or you install a new AP,
you must perform the Samsung Auto Configuration
procedure again, beginning from Step 1
English
2?