Schwinn 460 Elliptical Assembly Manual - Page 14

Step 8, Attach the Round Pedal Arms, to the Swing Arms

Get Schwinn 460 Elliptical PDF manuals and user guides View all Schwinn 460 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Assembly Step 8: Attach the Round Pedal Arms to the Swing Arms Parts • Main Assembly from Step 7 Hardware • #30 - M10 Spring Lock Washer (Qty 2) • #31 - M10 Wide Flat Washer (Qty 4) • #32 - M10 Hex Lock Nut (Qty 2) • #34 - M10 x 85 Button Head Bolt (Qty 2) Tools • 6mm Hex Key • C ombination Wrench (or 17mm socket wrench not included) Note: This step requires two people. 8-1 Have one person adjust the Cam Assembly, by rotating it from the Foot Pad until the holes of the Round Pedal Arm (A2) and the lower holes (H2) in the Swing Arm bracket align. 8-2 Attach the front end of the Round Pedal Arm to the bottom holes in the Swing Arm with one M10 x 85 Button Head Bolt, two M10 Wide Flat Washers, one M10 Spring Lock Washer and one Hex Lock Nut. 8-3 Tighten all hardware on Square and Round Pedal Arms. 8-4 Repeat Steps 6 thru 8 on opposite side. 32 31 31 30 34 H2 A2 Figure 8 12 Assembly Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Assembly Manual
12
Assembly
32
31
30
34
H2
31
A2
Step 8:
Attach the Round Pedal Arms
to the Swing Arms
Parts
•
Main Assembly from Step 7
Hardware
• #30 - M10 Spring Lock Washer (Qty 2)
• #31 - M10 Wide Flat Washer (Qty 4)
• #32 - M10 Hex Lock Nut (Qty 2)
• #34 - M10 x 85 Button Head Bolt (Qty 2)
Tools
• 6mm Hex Key
• Combination Wrench (or 17mm socket wrench -
not included)
Figure 8
Note:
This step requires two people.
8-1
Have one person adjust the Cam Assembly, by
rotating it from the Foot Pad until the holes of the
Round Pedal Arm (A2) and the lower holes (H2) in the
Swing Arm bracket align.
8-2
Attach the front end of the Round Pedal Arm to the
bottom holes in the Swing Arm with one M10 x 85
Button Head Bolt, two M10 Wide Flat Washers, one
M10 Spring Lock Washer and one Hex Lock Nut.
8-3
Tighten all hardware on Square and Round Pedal
Arms.
8-4
Repeat Steps 6 thru 8 on opposite side.