Schwinn 490 Elliptical Assembly and Owners Manual - Page 42

Console Setup Mode

Get Schwinn 490 Elliptical PDF manuals and user guides View all Schwinn 490 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

CONSOLE SETUP MODE The Console Setup Mode allows you to set units of measurement to either Imperial or metric, adjust screen brightness, view maintenance statistics (such as Run Time hours and software version - for service technician use only), or reset the Console. 1. Push the Programs button and hold for 3 seconds while in the Power-Up Mode to go into the Console Setup Mode (System Menu). Note: Push the Pause/Stop button to exit the System Menu and return to the Power-Up Mode screen. 2. The Console display shows the System Units prompt with the current setting. The default setting is Imperial English units. Push the Resistance Increase/Decrease buttons to change between Imperial (MI/LB) and metric (KM/KG). Note: If the units change when there is data in User Statistics, the statistics convert to the new units. 3. Push the Programs button to set the selection and continue to the next menu option. Note: T o save the selection and exit the System Menu, push the Start button. To exit without saving, push the Pause/ Stop button. 4. The Console display shows the Screen Brightness prompt with the current setting. The 5 levels of brightness are: 5 (100%), 4 (default, 95%), 3 (90%), 2 (85%), 1 (80%). The display shows the brightness of the selected level. Push the Resistance Increase/Decrease buttons to move to the desired level. 5. Push the Programs button to set the selection and continue to the next menu option. 6. The Console display shows the Disconnect Bluetooth prompt. The default option is NO. The YES option will disconnect all Bluetooth® devices. Push the Resistance Increase/Decrease buttons to change between options (YES/NO). 7. Push the Programs button to set the selection and continue to the next menu option. 8. The Console display shows the Auto Connect HR (Heart Rate) prompt. The default option is YES. Push the Resistance Increase/Decrease buttons to change between options (YES/NO). 9. Push the Programs button to set the selection and continue to the next menu option. 10. The Console display shows the Hardware Variant & Console Firmware Version. 11. Push the Programs button to continue to the next menu option. 12. The Console display shows the Base Serial Number. 13. Push the Programs button to continue to the next menu option. 14. The Console display shows the Hardware Variant (machine type). 15. Push the Programs button to set the selection and continue to the next menu option. 16. The Console display shows the Run Time hours (total number of hours of workout time). 17. Push the Programs button to continue to the next menu option. 18. The Console display shows the BLE Version. 19. Push the Programs button to continue to the next menu option. 20. The Console display shows the BTC Version. 21. Push the Programs button to continue to the next menu option. 22. The Console display shows the SENSOR Version. 23. Push the Programs button to continue to the next menu option. 24. The Console display shows the Error Log prompt (for service technician use only). Push the Resistance Decrease button to move through the logged errors. At the end of the logged errors, the Console display shows the Clear Errors prompt (for service technician use only). To clear the errors, push the Start button. 25. Push the Programs button to continue to the next menu option. 26. The Console display shows the Reset Console prompt. The default option is NO. Push the Pause/Stop button to exit 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
42
The Console Setup Mode allows you to set units of measurement to either Imperial or metric, adjust screen brightness,
view maintenance statistics (such as Run Time hours and software version – for service technician use only), or reset the
Console.
1.
Push the Programs button and hold for 3 seconds while in the Power-Up Mode to go into the Console Setup Mode
(System Menu).
Note:
Push the
Pause/Stop button to exit the System Menu and return to the Power-Up Mode screen.
2.
The Console display shows the System Units prompt with the current setting. The default setting is Imperial English
units. Push the Resistance Increase/Decrease buttons to change between Imperial (MI/LB) and metric (KM/KG).
Note:
If the units change when there is data in User Statistics, the statistics convert to the new units.
3.
Push the Programs button to set the selection and continue to the next menu option.
Note:
To save the selection and exit the System Menu, push the Start button. To exit without saving, push the Pause/
Stop button.
4.
The Console display shows the Screen Brightness prompt with the current setting. The 5 levels of brightness are: 5
(100%), 4 (default, 95%), 3 (90%), 2 (85%), 1 (80%). The display shows the brightness of the selected level. Push the
Resistance Increase/Decrease buttons to move to the desired level.
5.
Push the Programs button to set the selection and continue to the next menu option.
6.
The Console display shows the Disconnect Bluetooth prompt. The default option is NO. The YES option will discon-
nect all Bluetooth
®
devices. Push the Resistance Increase/Decrease buttons to change between options (YES/NO).
7.
Push the Programs button to set the selection and continue to the next menu option.
8.
The Console display shows the Auto Connect HR (Heart Rate) prompt. The default option is YES. Push the Resis-
tance Increase/Decrease buttons to change between options (YES/NO).
9.
Push the Programs button to set the selection and continue to the next menu option.
10.
The Console display shows the Hardware Variant & Console Firmware Version.
11.
Push the Programs button to continue to the next menu option.
12.
The Console display shows the Base Serial Number.
13.
Push the Programs button to continue to the next menu option.
14.
The Console display shows the Hardware Variant (machine type).
15.
Push the Programs button to set the selection and continue to the next menu option.
16.
The Console display shows the Run Time hours (total number of hours of workout time).
17.
Push the Programs button to continue to the next menu option.
18.
The Console display shows the BLE Version.
19.
Push the Programs button to continue to the next menu option.
20.
The Console display shows the BTC Version.
21.
Push the Programs button to continue to the next menu option.
22.
The Console display shows the SENSOR Version.
23.
Push the Programs button to continue to the next menu option.
24.
The Console display shows the Error Log prompt (for service technician use only). Push the Resistance Decrease
button to move through the logged errors. At the end of the logged errors, the Console display shows the Clear Errors
prompt (for service technician use only). To clear the errors, push the Start button.
25.
Push the Programs button to continue to the next menu option.
26.
The Console display shows the Reset Console prompt. The default option is NO. Push the Pause/Stop button to exit
CONSOLE SETUP MODE