Sharp XL-HP500 Operation Manual - Page 14

Setting the clock - remote

Get Sharp XL-HP500 PDF manuals and user guides View all Sharp XL-HP500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

XL-HP500W Setting the clock ENGLISH 4 Press the TUNING/TIME ( or ) button to adjust the hour and then press the MEMORY/SET button. The clock should be set on the main unit. In this example, the clock is set for the 24-hour (0:00) display. 1 Press the ON/STAND-BY button to turn the power on. 2 Press the CLOCK button on the main unit and within 5 sec- onds, press the MEMORY/SET button. Basic Operation 3 Press the TUNING/TIME ( or ) button to select 24-hour or 12-hour display and then press the MEMORY/SET button. E-13 "0:00" The 24-hour display will appear. (0:00 - 23:59) "AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59) "AM 0:00" The 12-hour display will appear. (AM 0:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. [Refer to "Clearing all the memory (reset)" on page 30 for details.] " Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. " When the 12-hour display is selected, "AM" will change automatically to "PM". 5 Press the TUNING/TIME ( or ) button to adjust the min- utes and then press the MEMORY/SET button. " Press the TUNING/TIME ( or ) button once to advance the time by 1 minute. Hold it down to change the time in 5minute intervals. " The hour will not advance even if minutes advance from "59" to "00". To confirm the time display: Press the CLOCK button on the main unit or remote control. The time display will appear for about 5 seconds. Note: The "CLOCK" or time will flash at the push of the CLOCK button when the AC power supply is restored after a power failure or unplugging the unit. Readjust the clock as follows. To readjust the clock: Perform "Setting the clock" from step 1. If the time display is flashing, step 3 (for selecting the 24-hour or 12-hour display) will be skipped. To change the 24-hour or 12-hour display: 1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on page 30 for details.] 2 Perform "Setting the clock" from step 1. 02/8/6 XL-HP500W(A)2.fm

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
02/8/6
XL-HP500W(A)2.fm
E-13
ENGLISH
XL-HP500W
Basic Operation
Setting the clock
The clock should be set on the main unit.
In this example, the clock is set for the 24-hour (0:00) display.
To confirm the time display:
Note:
The "CLOCK" or time will flash at the push of the CLOCK button
when the AC power supply is restored after a power failure or
unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the time display is flashing,
step 3 (for selecting the 24-hour or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK button on the main unit and within 5 sec-
onds, press the MEMORY/SET button.
3
Press the TUNING/TIME (
or
) button to select 24-hour
or 12-hour display and then press the MEMORY/SET but-
ton.
"0:00"
The 24-hour display will appear.
(0:00 - 23:59)
"AM 12:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00"
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it
has been reset. [Refer to "Clearing all the memory (reset)" on
page 30 for details.]
4
Press the TUNING/TIME (
or
) button to adjust the hour
and then press the MEMORY/SET button.
"
Press the TUNING/TIME (
or
) button once to advance
the time by 1 hour. Hold it down to advance continuously.
"
When the 12-hour display is selected, "AM" will change au-
tomatically to "PM".
5
Press the TUNING/TIME (
or
) button to adjust the min-
utes and then press the MEMORY/SET button.
"
Press the TUNING/TIME (
or
) button once to advance
the time by 1 minute. Hold it down to change the time in 5-
minute intervals.
"
The hour will not advance even if minutes advance from "59"
to "00".
Press the CLOCK button on the main
unit or remote control.
The time display will appear for about 5
seconds.
1
Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 30 for details.]
2
Perform "Setting the clock" from step 1.