Sony HDR SR5 Service Manual - Page 11

E : 62 : 11 [Shift Lens Overheating Pitch] Occurred SR7/SR7E/SR8/SR8E, Address Data

Get Sony HDR SR5 - AVCHD 4MP 40GB High Definition Hard Disk Drive Camcorder PDF manuals and user guides
UPC - 027242719651
View all Sony HDR SR5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

ENGLISH JAPANESE 1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred (SR7/SR7E/SR8/SR8E) Connect by the SeusEX and perform the following process. Order Block Page Address Data Procedure 1 11 80 6BB2 01 Write the data. 2 11 80 7D46 F0 Write the data. 3 11 80 7D48 01 Write the data. (Note 1) 4 11 80 7D48 00 Write the data. 5 11 80 7D46 10 Write the data. 6 11 80 7D48 01 Write the data. (Note 1) 7 11 80 7D48 00 Write the data. 8 11 80 6BB2 00 Write the data. 9 Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move, replace the lens block (Note 2). When the shift lens moved, proceed to the order 10. 10 While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5721 in the periphery of IC5703 on the LD-228 board to check the output voltage varies. 11 If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied, proceed to the order 12. 12 Turn the power OFF. While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 13 on the LD-228 board, turn the power ON to check that the output voltage immediately after the power on change as shown in Fig. 2. If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not 14 change as shown in Fig. 2, inspect the camera control circuit (IC1803 of VC-504 board) pe riphery. Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 80, address: 7D48, data: 00, and then retry. Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation. HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2 1-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
1-4
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred (SR7/SR7E/SR8/SR8E)
Connect by the SeusEX and perform the following process.
Order Block
Page Address Data
Procedure
1
11
80
6BB2
01
Write the data.
2
11
80
7D46
F0
Write the data.
3
11
80
7D48
01
Write the data. (Note 1)
4
11
80
7D48
00
Write the data.
5
11
80
7D46
10
Write the data.
6
11
80
7D48
01
Write the data. (Note 1)
7
11
80
7D48
00
Write the data.
8
11
80
6BB2
00
Write the data.
9
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
10
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5721 in the
periphery of IC5703 on the LD-228 board to check the output voltage varies.
11
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
12
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703
13
on the LD-228 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14
change as shown in Fig. 2, inspect the camera control circuit (IC1803 of VC-504 board) pe
riphery.
Note 1:
Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 80, address:
7D48, data: 00, and then retry.
Note 2:
When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.