Sony HDR SR5 Service Manual - Page 9

Self-diagnosis Code Table, to perform GYRO Sensor Sensitivity Adjustment. - repair

Get Sony HDR SR5 - AVCHD 4MP 40GB High Definition Hard Disk Drive Camcorder PDF manuals and user guides
UPC - 027242719651
View all Sony HDR SR5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

ENGLISH JAPANESE 1-2-3. Self-diagnosis Code Table Self-diagnosis Code Block Detailed Function Code Symptom/State Correction Repaired by: C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery. C1 3 0 1 "Memory Stick Duo" is unformatted. "Memory Stick Duo" is broken. Format the "Memory Stick Duo". Insert a new "Memory Stick Duo". C 1 3 0 2 Disc access error Remove the power source. Reconnect it again and operate your camcorder again C3 2 6 0 Difficult to adjust focus (Cannot initialize focus) Retry turn the power on by the power switch. If it does not recover, check the focus MR sensor of lens block (pin ql, wa of CN5302 on the LD-228 board: SR5/SR5C/SR5E, pin qh, qk of CN5301 on the LD-228 board: SR7/SR7E/SR8/SR8E). If it is OK, check the focus motor drive IC (IC5404 on the LD-228 board). E 2 0 0 0 EEPROM data are rewritten. Make EEPROM data correct value. E 3 1 0 0 Drive fault Inspect or replacement of the hard disk drive. E6 1 1 0 Zoom operations fault (Cannot initialize zoom lens.) Inspect the lens block zoom MR sensor (pin qh, qk of CN5302 on the LD-228 board: SR5/SR5C/SR5E, pin w;, wa of CN5301 on the LD-228 board: SR7/SR7E/SR8/SR8E) when zooming is performed when the zoom lever is operated, and the zoom motor drive circuit (IC5404 on the LD-228 board) when zooming is not performed. The abnormalities in initialization of E6 1 1 1 the focus lens and the abnormalities in initialization of the zoom lens occurred Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code. simultaneously. Handshake correction function does not Inspect PITCH angular velocity sensors (SE8202 on the CM-076 E 6 2 0 0 work well. (With PITCH angular board: SR5/SR5C/SR5E, SE7202 on the CM-077 board: SR7/ velocity sensor output stopped.) SR7E/SR8/SR8E) peripheral circuits. Handshake correction function does not Inspect YAW angular velocity sensors (SE8201 on the CM-076 E 6 2 0 1 work well. (With YAW angular velocity board: SR5/SR5C/SR5E, SE7201 on the CM-077 board: SR7/ sensor output stopped.) SR7E/SR8/SR8E) peripheral circuits. E 6 2 0 2 Abnormality of IC for steadyshot. Refer to [1-3-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Occurred] (SR7/SR7E/SR8/SR8E only). E 62 0 3 IC for steadyshot and micro controller Inspect the steadyshot circuit (IC5703 on the LD-228 board) communication abnormality among. (SR7/SR7E/SR8/SR8E only). E 6 2 1 0 Shift lens initializing failure. SR7/SR7E/SR8/SR8E only: 1. Inspect the EEPROM (IC1804 on the VC-504 board). 2. Perform the STEADY HALL adjustment. (Note 1) 3. Replace the lens block. (Note 2) E 6 2 1 1 Shift lens overheating (Pitch). Refer to [1-3-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred] (SR7/SR7E/SR8/SR8E only). E 6 2 1 2 Shift lens overheating (Yaw). Refer to [1-3-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred] (SR7/SR7E/SR8/SR8E only). E 6 2 2 0 Abnormality of thermistor. Refer to [1-3-4. E : 62 : 20 (Abnormality of Thermistor) Occurred] (SR7/SR7E/SR8/SR8E only). E 9 1 0 1 Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. E9 4 0 0 Fault of writing to or erasing the flashmemory Inspect the flash memory (IC2201 on the VC-504 board). Note 1: Perform adjustment by referring to "STEADY HALL Adjustment" in Service Manual, ADJ. After the adjustment, be sure to perform "GYRO Sensor Sensitivity Adjustment". Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation. HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2 1-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
1-2
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-2-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
3
1
6
1
6
1
6
2
6
2
6
2
6
2
6
2
6
2
6
2
6
2
9
1
9
4
Detailed
Code
0
0
0
1
0
2
6
0
0
0
0
0
1
0
1
1
0
0
0
1
0
2
0
3
1
0
1
1
1
2
2
0
0
1
0
0
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
Disc access error
Difficult to adjust focus
(Cannot initialize focus)
EEPROM data are rewritten.
Drive fault
Zoom operations fault
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality of IC for steadyshot.
IC for steadyshot and micro controller
communication abnormality among.
Shift lens initializing failure.
Shift lens overheating (Pitch).
Shift lens overheating (Yaw).
Abnormality of thermistor.
Abnormality when flash is being charged.
Fault of writing to or erasing the
flashmemory
Self-diagnosis Code
Repaired by:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin
ql
,
wa
of
CN5302 on the LD-228 board: SR5/SR5C/SR5E, pin
qh
,
qk
of
CN5301 on the LD-228 board: SR7/SR7E/SR8/SR8E). If it is
OK, check the focus motor drive IC (IC5404 on the LD-228
board).
Make EEPROM data correct value.
Inspect or replacement of the hard disk drive.
Inspect the lens block zoom MR sensor (pin
qh
,
qk
of CN5302
on the LD-228 board: SR5/SR5C/SR5E, pin
w;
,
wa
of CN5301
on the LD-228 board: SR7/SR7E/SR8/SR8E) when zooming is
performed when the zoom lever is operated, and the zoom motor
drive circuit (IC5404 on the LD-228 board) when zooming is not
performed.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Inspect PITCH angular velocity sensors (SE8202 on the CM-076
board: SR5/SR5C/SR5E, SE7202 on the CM-077 board: SR7/
SR7E/SR8/SR8E) peripheral circuits.
Inspect YAW angular velocity sensors (SE8201 on the CM-076
board: SR5/SR5C/SR5E, SE7201 on the CM-077 board: SR7/
SR7E/SR8/SR8E) peripheral circuits.
Refer to [1-3-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
Occurred] (SR7/SR7E/SR8/SR8E only).
Inspect the steadyshot circuit (IC5703 on the LD-228 board)
(SR7/SR7E/SR8/SR8E only).
SR7/SR7E/SR8/SR8E only:
1. Inspect the EEPROM (IC1804 on the VC-504 board).
2. Perform the STEADY HALL adjustment. (Note 1)
3. Replace the lens block. (Note 2)
Refer to [1-3-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
Occurred] (SR7/SR7E/SR8/SR8E only).
Refer to [1-3-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
Occurred] (SR7/SR7E/SR8/SR8E only).
Refer to [1-3-4. E : 62 : 20 (Abnormality of Thermistor)
Occurred] (SR7/SR7E/SR8/SR8E only).
Checking of flash unit or replacement of flash unit.
Inspect the flash memory (IC2201 on the VC-504 board).
Note 1:
Perform adjustment by referring to “STEADY HALL Adjustment” in Service Manual, ADJ. After the adjustment, be sure
to perform “GYRO Sensor Sensitivity Adjustment”.
Note 2:
When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.