Sony STR-K700 Operating Instructions - Page 20

Calibrating, appropriate, settings, automatically

Get Sony STR-K700 - Fm Stereo/fm-am Receiver PDF manuals and user guides View all Sony STR-K700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Inserting batteries into the remote Insert two R6 (size-AA) batteries in the RM-AAU006 remote commander. Observe the correct polarity when installing batteries. 0 0 0 Notes • Do not leave the remote in an extremely hot or humid place. • Do not use a new battery with old ones. • Do not mix alkaline batteries and other kinds of batteries. • Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. • If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Tip Under normal conditions, the batteries should last for about 3 months. When the remote no longer operates the receiver, replace all the batteries with new ones. 6: Calibrating the appropriate settings automatically (AUTO CALIBRATION) This receiver is equipped with D.C.A.C. (Digital Cinema Auto Calibration) Technology which allows you to perform automatic calibration as follows: • Check the connection between each speaker and the receiver. • Adjust the speaker level. • Measure the distance of each speaker to your listening position. You can also adjust the speaker levels and balance manually. For details, see "7: Adjusting the speaker levels and balance (TEST TONE)" (page 23) Before you perform Auto Calibration 1 Connect the supplied ECM-AC2 optimizer microphone to the AUTO CAL MIC jack. 2 Place the optimizer microphone at your listening position. 3 Place the speakers so that the speakers are facing the optimizer microphone. 20us

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Inserting
batteries
into
the
remote
Insert
two
R6
(size
-AA)
batteries
in
the
RM-AAU006
remote
commander.
Observe
the
correct
polarity
when
installing
batteries.
0
0
0
Notes
•
Do
not
leave
the
remote
in
an
extremely
hot
or
humid
place.
•
Do
not
use
a
new
battery
with
old
ones.
•
Do
not
mix
alkaline
batteries
and
other
kinds
of
batteries.
•
Do
not
expose
the
remote
sensor
to
direct
sunlight
or
lighting
apparatuses.
Doing
so
may
cause
a
malfunction.
•
If
you
do
not
intend
to
use
the
remote
for
an
extended
period
of
time,
remove
the
batteries
to
avoid
possible
damage
from
battery
leakage
and
corrosion.
Tip
Under
normal
conditions,
the
batteries
should
last
for
about
3
months.
When
the
remote
no
longer
operates
the
receiver,
replace
all
the
batteries
with
new
ones.
6:
Calibrating
the
appropriate
settings
automatically
(AUTO
CALIBRATION)
This
receiver
is
equipped
with
D.C.A.C.
(Digital
Cinema
Auto
Calibration)
Technology
which
allows
you
to
perform
automatic
calibration
as
follows:
•
Check
the
connection
between
each
speaker
and
the
receiver.
•
Adjust
the
speaker
level.
•
Measure
the
distance
of
each
speaker
to
your
listening
position.
You
can
also
adjust
the
speaker
levels
and
balance
manually.
For
details, see
"7:
Adjusting
the
speaker
levels
and
balance
(TEST
TONE)"
(page
23)
Before
you
perform
Auto
Calibration
1
2
3
Connect
the
supplied
ECM-AC2
optimizer
microphone
to
the
AUTO
CAL
MIC
jack.
Place
the
optimizer
microphone
at
your
listening
position.
Place
the
speakers
so
that
the
speakers
are
facing
the
optimizer
microphone.
20us