TEAC TN-400S TN-400S manual multi-lingual - Page 17
Troubleshooting, Specifications
View all TEAC TN-400S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
ENGLISH Troubleshooting If you experience a problem with this unit, please check the following items before requesting service. Something other than this unit could also be the cause of the problem. Please also check that the connected devices are also being used properly. If it still does not operate correctly, contact the retailer where you purchased the unit. No power. ee Confirm that the AC adapter is plugged into an outlet. Then, press the STANDBY/ON button to turn the unit on (pages 14 and 15). There is no sound. ee When connecting this unit's analog audio output connectors to the audio input connectors of an amplifier or other equipment, set the PHONO EQ (audio output setting) switch to ON (page 14). Playback is not possible; there is noise. ee Raise the protector (page 15). ee Fingerprints and dust on a record can cause noise and the sound to skip. Use a commercially-available record cleaner to clean records (page 11). ee Clean the stylus (page 14). ee If the stylus is worn-out, replace it (page 14). The lifespan of a stylus depends on the use conditions, but it is usually about 300 hours. ee Place the unit as far away as possible from TVs, microwave ovens and other devices that emit electromagnetic waves. Noise occurs when a record is playing. ee Noise could occur if the stylus pressure is higher than cartridge's specified value. Readjust the stylus pressure so that it is the specified value (page 12). The pitch is wrong. ee Select the rotation speed indicated on the record (page 15). The sound is skipping. ee Vibrations will cause skipping. Place this unit in a stable location. ee Clean the record. ee Do not use scratched records. ee Balance the tone arm and readjust the stylus pressure (page 12). The stylus and sound might skip if the stylus pressure is lower than the cartridge's specified value. Specifications Turntable (platter) Drive system Belt drive Motor DC motor Rotation speed 33 1/3 rpm, 45 rpm, 78 rpm Rotation speed variation 2% Wow and flutter 0.2% SN ratio 67 dB or higher (A-weighted, 20 kHz LPF) Turntable (platter Aluminum die-cast 30cm (12") diameter Tone arm Arm type Static-balanced S-shaped tone arm Effective arm length 223 mm Stylus pressure variation range 0-5 g Acceptable cartridge weight 4.0-8.0 g Cartridge Type VM (equivalent to MM) Output voltage 4.5 mV (1 kHz, 5 cm/s) Stylus pressure 1.4 ±0.4 g Cartridge weight 6.5 ±0.2 g Included headshell weight 10 g (including screws, nuts and wires) oo The lifespan of a stylus depends on the use conditions but is usually about 300 hours. oo The cartridge installed in this unit is equivalent to the Audio-Technica AT100E VM Type cartridge. (The replacement stylus for the installed cartridge is green. It does not have an Audio-Technica mark.) Note: VM type cartridges have the same characteristics as MM type cartridges. oo Replacement stylus model: Audio-Technica ATN100E General AC adapter power Input AC 100 V - AC 240 V, 50-60 Hz Output DC 12 V, 500 mA Power consumption Standby 0.5 W or less On (START 1.5 W or less Weight 4.9 kg (10 7/8 lb) Operating temperature range 5°C to 35°C Dimensions (W × H × D) (including protrusions) When the dust cover is closed 420 × 117 × 356 mm (16 5/8" × 4 5/8" × 14 1/8") When the dust cover is open 420 × 381 × 402 mm (16 5/8" × 15" × 15 7/8") When the dust cover is removed 420 × 102 × 356 mm (16 5/8" × 4 1/8" × 14 1/8") oo Performance data is specified at 20°C. Included items Felt mat × 1 45 RPM adapter × 1 Counterweight × 1 Headshell × 1 Audio-Technica VM Type (dual magnet) stereo cartridge (equivalent to AT100E) preinstalled Turntable (platter) × 1 Dust cover × 1 Dust cover hinges × 2 RCA audio cable with grounding terminal × 1 AC adapter (GPE053A-V120050-Z) × 1 Owner's manual (this document) × 1 Output voltage PHONO EQ THRU 4.5 mV (1 kHz, 5 cm/s) ±3 dB PHONO EQ ON 230 mV (−13 dBV) Output connectors RCA USB port USB port that can receive power from computer USB buses (Full Speed USB connector type B USB bus power support 5 V, 500 mA Sampling frequency 8 kHz, 11.025 kHz, 16 kHz, 22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz Quantization bit depth 16-bit oo Specifications and appearance are subject to change without notice. oo Weight and dimensions are approximate. oo Illustrations in this owner's manual might differ slightly from production models. 17