Toshiba 32RV525RZ Owners Manual - Page 24

Programming the remote control, to control your other devices

Get Toshiba 32RV525RZ PDF manuals and user guides View all Toshiba 32RV525RZ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Chapter 3: Using the remote control REMOTE CONTROL KEY REC SLOW - SLOW + ANGLE SUB TITLE AUDIO EJECT Toshiba TV REC MENU* SLOW REW* SLOW FWD* Angle* Sub title* Audio* Eject* CABLE --- SAT (satellite) --- AUX 1 (VCR) Record (2 click AUX 2 (DVD or HTIB) --- ----DVD Angle DVD Sub title DVD Audio DVD Eject Programming the remote control to control your other devices Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote control to operate a non-Toshiba device (or a Toshiba device that it is not preprogrammed to operate), follow the steps below. For details on using the remote control to operate the device, see page 22. 1無 In the remote control code table ( page 25), find the code for your device. If more than one code is listed, try each one separately until you find one that works. 2無 Set the MODE SELECT switch to the type of device you are programming the remote control to operate - CABLE/ SAT (for a cable converter box or satellite receiver), AUX 1 (for a VCR or TV/VCR combo), or AUX 2 (for a DVD player or HTIB [home theater in a box]). 3無 While holding down , press the Channel Number buttons to enter the 3-digit code for your device. 4無 To test the code, turn on the device, point the remote control at it, and press . See notes below. • If the correct code was entered, the device will turn off. • If the device does not respond, repeat steps 1-4 using another code. • If the device does not respond to another code, you will need to use the remote control that came with the device. 5無 Remember to set the MODE SELECT switch back to "TV" to control the TV. 6無 For future reference, write down the code(s) you used: DEVICE CODE DEVICE CODE Note: •• In addition to POWER, confirm that all necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device's original remote control. •• Every time you change the batteries, you will need to reprogram the remote control. •• Some newer VCRs respond to either of two codes. These VCRs have a switch labeled "VCR1/VCR2." If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position ("VCR1" or "VCR2") and reprogram the remote control. 24 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Chapter 3: Using the remote control
24
REMOTE CONTROL
KEY
Toshiba TV
CABLE
SAT (satellite)
AUX 1
(VCR)
AUX 2 (DVD or
HTIB)
REC
REC MENU*
---
---
Record (2
click)
---
SLOW –
SLOW REW*
---
---
---
---
SLOW +
SLOW FWD*
---
---
---
---
ANGLE
Angle*
---
---
---
DVD Angle
SUB TITLE
Sub title*
---
---
---
DVD Sub title
AUDIO
Audio*
---
---
---
DVD Audio
EJECT
Eject*
---
---
---
DVD Eject
Programming the remote control
to control your other devices
Your Toshiba TV remote control is preprogrammed
to operate most Toshiba devices. To program your
TV remote control to operate a non-Toshiba device
(or a Toshiba device that it is not preprogrammed to
operate), follow the steps below. For details on using
the remote control to operate the device, see page 22.
1無
In the remote control code table (
page 25), find the
code for your device. If more than one code is listed,
try each one separately until you find one that works.
2無
Set the
MODE SELECT switch
to the type of device you are
programming the remote control to operate — CABLE/
SAT (for a cable converter box or satellite receiver), AUX
1 (for a VCR or TV/VCR combo), or AUX 2 (for a DVD
player or HTIB [home theater in a box])
.
3無
While holding down
, press the Channel Number
buttons to enter the 3-digit code for your device.
4無
To test the code, turn on the device, point the remote
control at it, and press
. See notes below.
•
If the correct code was entered, the device will
turn off.
•
If the device does not respond, repeat steps 1–4
using another code.
•
If the device does not respond to another code,
you will need to use the remote control that came
with the device.
5無
Remember to set the
MODE SELECT switch
back to
“TV” to control the TV.
6無
For future reference, write down the code(s) you used:
DEVICE
CODE
DEVICE
CODE
Note:
•
In addition to POWER, confirm that all necessary
keys on the TV remote control operate your device.
If some keys are not operational, repeat the device
code setup using another code (if other codes
are listed for your device). If, after trying all listed
codes, the necessary keys do not operate your
device, use the device’s original remote control.
•
Every time you change the batteries, you will need
to reprogram the remote control.
•
Some newer VCRs respond to either of two codes.
These VCRs have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and does not
respond to the codes for your VCR brand, set the
switch to the other position (“VCR1” or “VCR2”)
and reprogram the remote control.
Downloaded from
www.Manualslib.com
manuals search engine