Tripp Lite BP48V Eaton Tripp Lite SmartOnline Series Tower UPS Advanced User G - Page 28

Table 8. Signal Outputs Continued, Signal, Default Assignment, Description

Get Tripp Lite BP48V PDF manuals and user guides View all Tripp Lite BP48V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Remote Control Functions Table 8. Signal Outputs (Continued) Signal Load protected General alarm Battery Charging OVL pre-alarm Default Assignment - Description UPS is on inverter, with no alarm and ready to go to battery Choose events that will trigger this alarm trough the LCD Control an optional external battery charger on and off. Overload pre-alarm (1) Relay output: Normally Closed 1 Normally Open 2 Common 3 Connectivity Cards Connectivity cards allow the UPS to communicate in a variety of networking environments and with different types of devices. The Tripp Lite by Eaton SmartOnlineUPS models have one available communication bay for the following connectivity cards: • Network card (WEBCARDLXE) - Provides monitoring and control using an SNMP network management platform, web browser, SSH or Telnet. Figure 10. Connectivity Card Options STATUS CONFIG RESET Installation of the communication card (optional) NOTE Connect a Cat-6 shielded ethernet cable (F/UTP or F/FTP) or higher between the LX Platform device's ethernet port and a network jack It is not necessary to shutdown the UPS before installing a communication card. 22 Tripp Lite by Eaton SmartOnline Series User Guide 614-21326-Rev 01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
22
Tripp Lite by Eaton SmartOnline Series User Guide 614-21326—Rev 01
Table 8. Signal Outputs (Continued)
Signal
Default Assignment
Description
Loadprotected
-
UPSisoninverter,withnoalarmandreadytogo
tobattery
Generalalarm
-
Chooseeventsthatwilltriggerthisalarmtrough
theLCD
BatteryCharging
-
Controlanoptionalexternalbatterychargeron
andoff.
OVLpre-alarm
-
Overloadpre-alarm
(1) Relay output:
Normally Closed
Normally Open
Common
1
2
3
ConnectivityCards
Connectivity cards allow the UPS to communicate in a variety of networking environments and with different
types of devices. The Tripp Lite by Eaton SmartOnlineUPS models have one available communication bay for
the following connectivity cards:
•
Networkcard(WEBCARDLXE)
— Provides monitoring and control using an SNMP network management
platform, web browser, SSH or Telnet.
Figure10.ConnectivityCardOptions
CONFIG
STATUS
RESET
Installationofthecommunicationcard(optional)
NOTE
Connect a Cat-6 shielded ethernet cable (F/UTP or F/FTP) or higher between the LX
Platform device’s ethernet port and a network jack
It is not necessary to shutdown the UPS before installing a communication card.
RemoteControlFunctions