Whirlpool WDT730PAHV Installation Guide - Page 10

Built-up floors - add shims, as needed, If installing into a, 851 mm opening, ELECTRICAL CONNECTION,

Get Whirlpool WDT730PAHV PDF manuals and user guides View all Whirlpool WDT730PAHV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

5. Built-up floors - add shims as needed ELECTRICAL CONNECTION - For Direct Wire, begin with Step 7 - For Power Cord, wait until Step 22 7. Direct wire - route cable Built-up floors: If the kitchen floor is higher than the cabinet opening's floor - for example, the kitchen floor tile does not extend into the cabinet opening - add shims, as needed, in the area shown to bring the dishwasher up to 34" (864 mm) below the countertop. NOTE: Shims must be securely attached to floor to avoid movement when the dishwasher is in use. 6. If installing into a 331/2" (851 mm) opening If installing with direct wire, route the cable as shown. Route cable from power supply through cabinet hole. (Cable must extend to the right front side of cabinet opening.) Tape cable to the floor in area shown. This will prohibit cable from moving when dishwasher is moved into cabinet opening. NOTES: ■■ If removing a previous dishwasher with a power cord, you will need to transfer the power cord to the new dishwasher. ■■ Direct wire connection to the dishwasher will not be done until you get to Step 49. Cut insulation blanket along perforation for cabinet opening height of 331/2" (851 mm). For other cabinet opening heights, do not cut the insulation blanket. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
10
Built-up floors: If the kitchen floor is higher than the cabinet
opening’s floor – for example, the kitchen floor tile does not
extend into the cabinet opening – add shims, as needed, in the
area shown to bring the dishwasher up to 34" (864 mm) below
the countertop.
NOTE:
Shims must be securely attached to floor to avoid
movement when the dishwasher is in use.
Cut insulation blanket along perforation for cabinet opening
height of 33
1
/
2
" (851 mm). For other cabinet opening heights,
do not cut the insulation blanket.
5.
Built-up floors – add shims
as needed
6.
If installing into a
33
1
/
2
" (851 mm) opening
ELECTRICAL CONNECTION
– For Direct Wire, begin with Step 7
– For Power Cord, wait until Step 22
If installing with direct wire, route the cable as shown.
Route cable from power supply through cabinet hole. (Cable
must extend to the right front side of cabinet opening.) Tape
cable to the floor in area shown. This will prohibit cable from
moving when dishwasher is moved into cabinet opening.
NOTES:
■
If removing a previous dishwasher with a power cord, you will
need to transfer the power cord to the new dishwasher.
■
Direct wire connection to the dishwasher will not be done until
you get to Step 49.
7.
Direct wire – route cable