Whirlpool WDT730PAHV Installation Guide - Page 15

Power cord - reinstall terminal

Get Whirlpool WDT730PAHV PDF manuals and user guides View all Whirlpool WDT730PAHV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

WARNING Wiring configuration Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 27. Power cord - secure cord in strain relief 25. Power cord - connect ground wire Ground wire Tighten strain relief screws to secure cord. 28. Power cord - reinstall terminal box cover and wires Remove the ground connector screw and place it through the ring terminal of the green ground wire of power cord. Reattach and tighten the ground connector screw. 26. Power cord - connect remaining wires Place wires inside terminal box. Insert tabs on left side of cover. Make sure wires are tucked inside the box and not pinched by the cover. Use a 1/4" hex-head socket, nut driver, or Torx® T20® screwdriver, and the screw removed in Step 22 to secure the terminal box cover. If power cord supplied model, remove the first tie strap closest to the plug to maximize the cord length. Do not remove any other tie straps. NOTE: Route power cord out the rear of the dishwasher. Do not plug cord into an outlet until instructed to do so. Select UL Listed/CSA Approved twist-on wire connectors of the proper size. See the "Tools and Parts" section at the front of the guide for part details. Connect wires, black to black and white to white, using the twist-on wire connectors. NOTE: Do not pre-twist stranded wire. Twist on wire connector. Gently tug on wires to be sure both are secured. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
15
Tighten strain relief screws to secure cord.
Place wires inside terminal box. Insert tabs on left side of cover.
Make sure wires are tucked inside the box and not pinched by
the cover. Use a
1
/
4
" hex-head socket, nut driver, or Torx
®
T20
®
screwdriver, and the screw removed in Step 22 to secure the
terminal box cover.
If power cord supplied model, remove the first tie strap closest
to the plug to maximize the cord length. Do not remove any
other tie straps.
NOTE:
Route power cord out the rear of the dishwasher.
Do not plug cord into an outlet until instructed to do so.
Wiring configuration
27.
Power cord – secure cord
in strain relief
28.
Power cord – reinstall terminal
box cover and wires
Remove the ground connector screw and place it through the
ring terminal of the green ground wire of power cord. Reattach
and tighten the ground connector screw.
Select UL Listed/CSA Approved twist-on wire connectors of
the proper size. See the “Tools and Parts” section at the front
of the guide for part details. Connect wires, black to black and
white to white, using the twist-on wire connectors.
NOTE:
Do not pre-twist stranded wire. Twist on wire connector.
Gently tug on wires to be sure both are secured.
WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
25.
Power cord – connect ground wire
Ground
wire
26.
Power cord – connect
remaining wires