Whirlpool WGD9500T Use and Care Manual - Page 16
feature and Cycle Signal. During the Quick Refresh
View all Whirlpool WGD9500T manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
The default dryness setting is Normal when an Auto Dry Cycle is selected. You can select a different dryness level, depending on your load, by pressing DRYNESS LEVEL and choosing More, Normal or Less. Selecting More, Normal or Less automatically adjusts the dryness level at which the dryer will shut off. Once a dryness level is set, it cannot be changed without stopping the cycle. The Dryness Level can be changed only with Automatic Cycles. • Press the WRINKLE SHIELD TM feature button if this option is desired. • Press the CYCLE SIGNAL button to set end of cycle signal volume to desired level. • Press the DAMP DRY CYCLE SIGNAL button to set damp dry signal volume to desired level. • Press and hold START button until dryer starts (about 1 second). Once an Automatic cycle has started, the WRINKLE SHIELD TM feature and cycle signals can be adjusted. Press the PAUSE/CANCEL key twice to clear the settings, allowing you to select another cycle and Dryness Level. NOTE: Time and Temperature are not adjustable for Automatic Cycles. Pressing the DRY TIME or TEMPERATURE buttons will cause a triple beep, indicating that the time cannot be changed. How Automatic Cycles Work The AccelerCare TM function improves drying performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they tumble. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level selected and amount of moisture left in the clothes. When the clothes have reached approximately 80% of the dryness level selected, the estimated time display will adjust again, showing the final drying time. The AccelerCare TM feature takes the guesswork out of drying time and enhances fabric care. To use a Manual Cycle NOTE: A light next to each feature will glow green when the feature is selected or will glow amber when the feature is selectable. The light will not glow when the selection is unavailable with the cycle or option combinations selected. • Press POWER. Rotate the dial to select a Manual Cycle. Press the DRY TIME up or down buttons until the desired drying time is displayed. Press DRY TIME, and the time will change by 1-minute intervals. Press and hold DRY TIME, and the time will change by 5-minute intervals. The initial time displayed is the actual drying time. AdjustManual ®®DryTime The Dry Time feature can be used only with Manual Cycles and the Enhanced Touch Up Cycle. Press TEMPERATURE until the desired temperature glows green. High Medium Low Extra Low Air Only Temperature AdjustManual Cycle0snly Temperature settings can be changed only with Manual Cycles. • Press the WRINKLE SHIELD TM feature button if this option is desired. • Press the CYCLE SIGNAL button to set end of cycle signal volume to desired level. • Press and hold START button until dryer starts (about 1 second). NOTE: Dryness Level is not adjustable for Manual or Steam Cycles. Pressing the Dryness Level button will cause the triple beep indicating that this option is not selectable. While a Manual Cycle is running, you cannot change the cycle until you clear the settings. You can change the settings for Time, Temperature, the WRINKLE SHIELD TM feature and the cycle signals. Press the PAUSE/CANCEL key twice to clear the settings, allowing you to select another cycle. To use a Steam Cycle • Press the POWER button. Rotate the dial to select either the Enhanced Touch Up or Quick Refresh cycles. Press the DRY TIME up or down buttons until the desired drying time is displayed. Press DRY TIME, and the time will change by 1-minute intervals. Press and hold DRY TIME, and the time will change by 5-minute intervals. The initial time displayed is the actual drying time NOTE: The More Time and Less Time buttons can be used only with Manual Cycles and the Enhanced Touch Up Cycle. AdjustManual ®®Dry Time • Press TEMPERATURE until the desired temperature glows green. NOTE: During the Enhanced Touch Up Cycle, you can change the settings for Time, Temperature, the WRINKLE SHIELD TM feature and Cycle Signal. During the Quick Refresh Cycle you can change the WRINKLE SHIELD TM feature and the Cycle Signal. Press STOP twice to stop the dryer and clear the settings. Select another cycle or option. 16