Home » Xerox Manuals » Multifunction Devices » Xerox 3210 » Manual Viewer

Xerox 3210 User Guide - Page 75

One is, Open/Close Door - toner exhausted

UPC - 095205754322

Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

MESSAGE MEANING SUGGESTED SOLUTIONS Memory Full The memory is full. Delete unnecessary fax jobs and retransmit after more memory becomes available. Alternatively, split the transmission into more than one operation. Not Assigned The speed button or speed dial number you tried to use has no number assigned to it. Enter the number manually using the number keypad or store the number or address. One Page is Too Large Single page data exceeds the configured mail size. Reduce the resolution and try again. Operation Not Assigned You are in the Add Page/Cancel Job operation, but there are no jobs stored. Check the display to see if there are any scheduled jobs. Out-Bin Full| The output tray of the Remove paper. Open the Open/Close Door machine is full of front cover and than close paper. it. Paper Jam 0 Paper has jammed in Clear the jam. See page Open/Close Door the feeding area of the 70. tray. Paper Jam 1 Paper has jammed Open/Close Door inside the machine. Clear the jam. See page 71. Paper Jam 2 Check Inside Special print media has jammed in the paper exit area. Clear the jam. See page 71. Refilled Toner T The print cartridge you have installed is not genuine or refilled. The print quality may get poor if the refilled print cartridge is installed, since its characteristics may significantly differ from the genuine. We recommend Xeroxgenuine print cartridge. Replace Toner T This message appears between Toner Empty and Toner Low status. Replace the print cartridge with a new one. See page 65. Replace [xxx] Soon The life of the part expires soon. See page 66 and call for service. Retry Redial? The machine is waiting for a specified time interval to redial a previously busy station. You can press OK to immediately redial, or Stop/Clear to cancel the redial operation. Send Error (AUTH) There is a problem in Configure the SMTP authentication. authentication setting. 74 _Troubleshooting MESSAGE MEANING SUGGESTED SOLUTIONS Send Error (DNS) There is a problem in Configure the DNS setting. DNS. Send Error (POP3) There is a problem in Configure the POP3 POP3. setting. Send Error (SMTP) There is a problem in Change to the available SMTP. server. Send Error (Wrong Config) There is a problem on Configure your network the network interface interface card correctly. card. Toner Empty T The print cartridge has run out. The machine stops printing. Press OK to toggle the message to Stop or Continue. W Stop X You can select the option among Stop or Continue with the left/right arrow. If you select Stop by pressing OK on the control panel, the machine stops printing. If you select Continue, the machine keeps printing, but the quality cannot be guaranteed. If you do not select any, the machine will work as Stop is selected. Replace the print cartridge with a new one. See page 65. Toner Exhausted T The lifespan of the print cartridge which the arrow indicates is reached. This message appears when the toner is completely empty, and your machine stops printing. Replace the corresponding print cartridge with a Xeroxgenuine cartridge. See page 65. Toner Low T The corresponding print cartridge is almost empty. Take out the print cartridge and thoroughly shake it. By doing this, you can temporarily reestablish printing operations. Updating Data Please Wait... This message appears when there is a change in the system setting or when you back up a data. Do not turn the power off when this message is showing. Changes may not be saved and datas can be lost.

Section	Page
Contents	2
Features of your new laser product	7
Safety	10
Regulatory Information	13
Introduction	20
Printer overview	20
Front view	20
Rear view	20
Control panel overview	21
Understanding the Status LED	22
Menu overview	23
Supplied software	24
Printer driver features	24
Printer driver	24
PostScript driver (WorkCentre 3220 only)	25
Getting started	26
Setting up the hardware	26
System requirements	26
Windows	26
Macintosh	27
Linux	27
Setting up the network	27
Introduction	27
Supported operating systems	27
Locating the WorkCentre 3210 or WorkCentre 3220 IP Address	28
Accessing CentreWare Internet Services (CWIS)	28
Configuring network protocol via the machine	28
Setting Ethernet speed	28
Restoring the network configuration	28
Printing a network configuration page	28
Using SetIP program	28
Installing the software	29
Machine's basic settings	30
Altitude adjustment	30
Changing the display language	30
Setting the date and time	30
Changing the clock mode	30
Changing the default mode	31
Setting sounds	31
Entering characters using the number keypad	31
Using the save modes	32
Setting print job timeout	32
Changing the font setting	32
Loading originals and print media	33
Loading originals	33
On the scanner glass	33
In the ADF	33
Selecting print media	34
Specifications on print media	35
Media sizes supported in each mode	36
Guidelines for selecting and storing print media	36
Guidelines for special print media	36
Changing the size of the paper in the paper tray	37
Loading paper	38
Loading paper in the tray 1 or optional tray	38
Printing on special print materials	38
Adjusting the output support	39
Stacking papers firmly	39
Setting the paper size and type	39
Copying	40
Selecting the paper tray	40
Copying	40
Changing the settings for each copy	40
Darkness	40
Original Type	40
Reduced or enlarged copy	40
Changing the default copy settings	41
ID card copying	41
Using special copy features	41
Collation	41
2-up or 4-up copying	42
Poster copying	42
Clone copying	42
Adjusting background images	42
Printing on both sides of paper	43
Setting copy timeout	43
Scanning	44
Scanning basics	44
Scanning from the control panel	44
Scanning to application programs for USB connections	44
Scanning using a network connection	44
Preparing for network scanning	44
Scanning to a network client	45
Scanning to Email	45
Changing the settings for each scan job	46
Changing the default scan settings	46
Setting up Address Book	46
Registering speed email numbers	46
Configuring group email numbers	46
Using Address Book entries	46
Searching Address Book for an entry	47
Printing Address Book	47
Basic printing	48
Printing a document	48
Canceling a print job	48
Faxing	49
Sending a fax	49
Setting the fax header	49
Adjusting the document settings	49
Sending a fax automatically	50
Sending a fax manually	50
Confirming a transmission	50
Automatic redialing	50
Redialing the last number	50
Receiving a fax	50
Selecting the paper tray	50
Changing receiving modes	50
Receiving automatically in Fax mode	51
Receiving manually in Tel mode	51
Receiving manually using an extension telephone	51
Receiving automatically in Ans/Fax mode	51
Receiving faxes using DRPD mode	51
Receiving in secure receiving mode	52
Activating secure receiving mode	52
Receiving faxes in memory	52
Other ways to fax	52
Sending a fax to multiple destinations	52
Sending a delayed fax	52
Sending a priority fax	53
Forwarding faxes	53
Sending a Fax from a PC	54
Fax setup	55
Changing the fax setup options	55
Changing the default document settings	56
Printing sent fax report automatically	57
Setting up Address Book	57
Using USB flash memory	59
About USB memory	59
Plugging in a USB memory device	59
Scanning to a USB memory device	59
Scanning	59
Customizing Scan to USB	60
Printing from a USB memory device	60
To print a document from a USB memory device:	60
Backing up data	60
Backing up data	60
Restoring data	60
Managing USB memory	61
Deleting an image file	61
Formatting a USB memory device	61
Viewing the USB memory status	61
Maintenance	62
Printing reports	62
Printing a report	62
Clearing memory	63
Firmware update	63
Cleaning your machine	63
Cleaning the outside	63
Cleaning the inside	63
Cleaning the scan unit	64
Maintaining the cartridge	65
Print cartridge storage	65
Expected cartridge life	65
Redistributing toner	65
Replacing the print cartridge	66
Cleaning the drum	67
Clearing the Toner Empty message	67
Maintenance parts	67
Checking replaceables	67
Replacing the ADF rubber pad	67
Replacing the ADF feed roller	68
Replacing the transfer roller	68
Replacing the pick up roller	69
Managing your machine from the website	69
Checking the machine’s serial number	69
Troubleshooting	70
Tips for avoiding paper jams	70
Clearing document jams	70
Input Misfeed	70
Exit misfeed	71
Roller misfeed	71
Clearing paper jams	71
In the paper feed area	71
In the manual tray	72
In the print cartridge area	72
In the paper exit area	72
In the duplex unit area	72
In the optional tray	73
Understanding display messages	74
Solving other problems	76
Paper feeding	76
Printing problems	76
Printing quality problems	77
Copying problems	79
Scanning problems	80
Network Scan problems	81
Fax problems	81
Common PostScript problems (WorkCentre 3220 only)	82
Common Windows problems	82
Common Linux problems	82
Common Macintosh problems	83
Ordering supplies and accessories	84
Supplies	84
Accessories	84
How to purchase	84
Installing accessories	85
Precautions to take when installing accessories	85
Upgrading a memory module	85
Installing a memory module	85
Activating the added memory in the PS printer properties	86
Specifications	87
General specifications	87
Printer specifications	88
Scanner specifications	88
Copier specifications	89
Facsimile specifications	89
Glossary	90
Index	94
Software section	96
Software section Contents	97
Installing Printer Software in Windows	100
Installing Printer Software	100
Installing Software for Local Printing	100
Installing Software for Network Printing	102
Reinstalling Printer Software	105
Removing Printer Software	106
Using SetIP	107
Installing SetIP	107
Using SetIP	108
Basic Printing	109
Printing a Document	109
Printing to a file (PRN)	110
Printer Settings	110
Layout Tab	111
Paper Tab	111
Graphics Tab	112
Extras Tab	113
About Tab	114
Printer Tab	114
Using a Favorite Setting	114
Using Help	114
Advanced Printing	115
Printing Multiple Pages on One Sheet of Paper (N-Up Printing)	115
Printing Posters	116
Printing Booklets	116
Printing on Both Sides of Paper	117
Printing a Reduced or Enlarged Document	117
Fitting Your Document to a Selected Paper Size	117
Using Watermarks	118
Using an Existing Watermark	118
Creating a Watermark	118
Editing a Watermark	118
Deleting a Watermark	118
Using Overlays	119
What is an Overlay?	119
Creating a New Page Overlay	119
Using a Page Overlay	119
Deleting a Page Overlay	119
Using Windows PostScript Driver (WorkCentre 3220)	120
Printer Settings	120
Advanced	120
Using Help	120
Sharing the Printer Locally	121
Setting Up a Host Computer	121
Setting Up a Client Computer	121
Scanning	122
Scanning Process with TWAIN- enabled Software	122
Scanning Using the WIA Driver	122
Windows XP	122
Windows Vista	122
Using Utility Applications	123
Using Printer Settings Utility	123
Using Onscreen Help	123
Opening the Troubleshooting Guide	123
Changing the Status Monitor Program Settings	123
Using Your Printer in Linux	124
Getting Started	124
Installing the Unified Linux Driver	124
Installing the Unified Linux Driver	124
Uninstalling the Unified Linux Driver	125
Using the Unified Driver Configurator	126
Opening the Unified Driver Configurator	126
Printers Configuration	126
Scanners Configuration	127
Ports Configuration	127
Configuring Printer Properties	128
Printing a Document	128
Printing from Applications	128
Printing Files	129
Scanning a Document	129
Using the Image Manager	130
Using Your Printer with a Macintosh	132
Installing Software	132
Installing printer software	132
Uninstalling printer software	132
Setting Up the Printer	133
For a Network-connected	133
For a USB-connected	134
Installable Options	134
Printing	135
Printing a Document	135
Changing Printer Settings	135
Printing Multiple Pages on One Sheet of Paper	137
Duplex Printing	137
Scanning	138
Scanning with USB	138

Match case Limit results 1 per page

74 _

Troubleshooting

Memory Full

The memory is full.

Delete unnecessary fax

jobs and retransmit after

more memory becomes

available. Alternatively,

split the transmission into

more than one operation.

Not Assigned

The speed button or

speed dial number

you tried to use has

no number assigned

to it.

Enter the number

manually using the

number keypad or store

the number or address.

One Page is

Too Large

Single page data

exceeds the

configured mail size.

Reduce the resolution and

try again.

Operation Not

Assigned

You are in the

Add

Page

Cancel Job

operation, but there

are no jobs stored.

Check the display to see if

there are any scheduled

jobs.

Out-Bin Full|

Open/Close Door

The output tray of the

machine is full of

paper.

Remove paper. Open the

front cover and than close

it.

Paper Jam 0

Open/Close Door

Paper has jammed in

the feeding area of the

tray.

Clear the jam. See page

70.

Paper Jam 1

Open/Close Door

Paper has jammed

inside the machine.

Clear the jam. See page

71.

Paper Jam 2

Check Inside

Special print media

has jammed in the

paper exit area.

Clear the jam. See page

71.

Refilled Toner

The print cartridge you

have installed is not

genuine or refilled.

The print quality may get

poor if the refilled print

cartridge is installed, since

its characteristics may

significantly differ from the

genuine.

We recommend Xerox-

genuine print cartridge.

Replace Toner

This message

appears between

Toner Empty

and

Toner Low

status.

Replace the print cartridge

with a new one. See page

65.

Replace

[xxx] Soon

The life of the part

expires soon.

See page 66 and call for

service.

Retry Redial?

The machine is

waiting for a specified

time interval to redial

a previously busy

station.

You can press

immediately redial, or

Stop/Clear

to cancel

the redial operation.

Send Error

(AUTH)

There is a problem in

SMTP authentication.

Configure the

authentication setting.

MESSAGE

MEANING

SUGGESTED

SOLUTIONS

Send Error

(DNS)

There is a problem in

DNS.

Configure the DNS setting.

Send Error

(POP3)

There is a problem in

POP3.

Configure the POP3

setting.

Send Error

(SMTP)

There is a problem in

SMTP.

Change to the available

server.

Send Error

(Wrong Config)

There is a problem on

the network interface

card.

Configure your network

interface card correctly.

Toner Empty

The print cartridge has

run out. The machine

stops printing.

Press

to toggle

the message to

Stop

Continue

Stop

You can select the option

among

Stop

Continue

with the left/right arrow.

If you select

Stop

pressing

on the control

panel, the machine stops

printing. If you select

Continue

, the machine

keeps printing, but the

quality cannot be

guaranteed.

If you do not select any,

the machine will work as

Stop

is selected.

Replace the print cartridge

with a new one. See page

65.

Toner Exhausted

The lifespan of the

print cartridge which

the arrow indicates is

reached.

This message appears

when the toner is

completely empty, and

your machine stops

printing. Replace the

corresponding print

cartridge with a Xerox-

genuine cartridge. See

page 65.

Toner Low

The corresponding

print cartridge is

almost empty.

Take out the print cartridge

and thoroughly shake it.

By doing this, you can

temporarily reestablish

printing operations.

Updating Data

Please Wait...

This message

appears when there is

a change in the

system setting or

when you back up a

data.

Do not turn the power off

when this message is

showing. Changes may

not be saved and datas

can be lost.

MESSAGE

MEANING

SUGGESTED

SOLUTIONS