Xerox 4510N User Guide - Page 32

Setting the Interface ID, Resetting the TCP/IP Configuration, Using CentreWare IS

Get Xerox 4510N - Phaser B/W Laser Printer PDF manuals and user guides
UPC - 095205427813
View all Xerox 4510N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

IPv6 Resetting the TCP/IP Configuration Use the following procedure at the control panel to reset the TCP/IP configuration to the default settings: 1. Select Printer Setup, and then press the OK button. 2. Select Connection Setup, and then press the OK button. 3. Select Reset Connection Setup, and then press the OK button. Setting the Interface ID Your IPv6-enabled printer has one interface with multiple addresses. The Interface ID appears after the prefix. The printer uses the Interface ID when assigning both the Link-Local address and automatic addresses that use router-supplied prefix(es). It is not used in addresses supplied by DHCPv6. Link-Local addresses are used by nodes to communicate with other nodes on the same local network. There are two ways to set the Interface ID: ■ Automatic (default): The Interface ID is identified from the MAC address associated with the interface and different for each device. ■ Manual: When using this option, verify that the interface ID is 64 bits (8 bytes) and does not contain certain special characters other than colons or valid hexadecimal digits (0 through 9, a through f, or A through F). Note: If you change the Interface ID, you are prompted to reset the printer before the changes take effect. The Interface ID can only be set in CentreWare IS. Using CentreWare IS To set the Interface ID using CentreWare IS: 1. Launch your web browser. 2. Enter your printer's IP address in the browser's Address field. 3. Click Properties. 4. Select the Protocols folder on the left navigation panel, and then click TCP/IP. 5. Click the TCP/IP (v6) button. 6. Do one of the following: ■ Select User Interface ID from MAC address. ■ Select Use this Interface ID. 7. Click the Save Changes button at the bottom of the page. Phaser® 4510 Laser Printer 2-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
IPv6
Phaser® 4510 Laser Printer
2-15
Resetting the TCP/IP Configuration
Use the following procedure at the control panel to reset the TCP/IP configuration to the
default settings:
1.
Select
Printer Setup
, and then press the
OK
button.
2.
Select
Connection Setup
, and then press the
OK
button.
3.
Select
Reset Connection Setup
, and then press the
OK
button.
Setting the Interface ID
Your IPv6-enabled printer has one interface with multiple addresses. The Interface ID appears
after the prefix. The printer uses the Interface ID when assigning both the Link-Local address
and automatic addresses that use router-supplied prefix(es). It is not used in addresses supplied
by DHCPv6. Link-Local addresses are used by nodes to communicate with other nodes on the
same local network. There are two ways to set the Interface ID:
■
Automatic
(default): The Interface ID is identified from the MAC address associated with
the interface and different for each device.
■
Manual:
When using this option, verify that the interface ID is 64 bits (8 bytes) and
does not contain certain special characters other than colons or valid hexadecimal digits (0
through 9, a through f, or A through F).
Note:
If you change the Interface ID, you are prompted to reset the printer before the changes
take effect.
The Interface ID can only be set in CentreWare IS.
Using CentreWare IS
To set the Interface ID using CentreWare IS:
1.
Launch your web browser.
2.
Enter your printer’s IP address in the browser’s
Address
field.
3.
Click
Properties
.
4.
Select the
Protocols
folder on the left navigation panel, and then click
TCP/IP
.
5.
Click the
TCP/IP (v6)
button.
6.
Do one of the following:
■
Select
User Interface ID from MAC address
.
■
Select
Use this Interface ID
.
7.
Click the
Save Changes
button at the bottom of the page.