Xerox 4510N User Guide - Page 97

Setting the Fuser Temperature

Get Xerox 4510N - Phaser B/W Laser Printer PDF manuals and user guides
UPC - 095205427813
View all Xerox 4510N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Solving Print-Quality Problems Setting the Fuser Temperature If the printed image is not fully fused to the paper and easily rubs off, adjusting the fuser temperature may produce better results. The printer has six fuser temperatures that can be configured for each media type. Heavier and high cotton content media usually requires a higher temperature to sufficiently bond the toner to the paper. Some label media and other heat-sensitive media require low temperature to avoid detaching from the backing or warping. See also: Unfused or Partially Fused Image on page 4-12 Using the Control Panel To select the fuser temperature using the control panel: 1. Select Printer Setup, and then press the OK button. 2. Select Paper Handling Setup, and then press the OK button. 3. Select Fuser Configuration, and then press the OK button. 4. Select the appropriate media, and then press the OK button. 5. Select the desired fuser temperature, Extra High, Very High, High, Medium, Low, or Very Low and then press the OK button. Using CentreWare IS To select the fuser temperature using CentreWare IS: 1. Launch your web browser. 2. Enter the printer's IP address in the browser's Address field (http://xxx.xxx.xxx.xxx). 3. Click Properties. 4. Select General on the left navigation panel, and then select Fuser. 5. Use the appropriate media drop-down list to change the fuser temperature. 6. Click the Save Changes button at the bottom of the page. Phaser® 4510 Laser Printer 4-16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-16
Setting the Fuser Temperature
If the printed image is not fully fused to the paper and easily rubs off, adjusting the fuser
temperature may produce better results.
The printer has six fuser temperatures that can be configured for each media type. Heavier and
high cotton content media usually requires a higher temperature to sufficiently bond the toner
to the paper. Some label media and other heat-sensitive media require low temperature to avoid
detaching from the backing or warping.
See also:
Unfused or Partially Fused Image
on page 4-12
Using the Control Panel
To select the fuser temperature using the control panel:
1.
Select
Printer Setup
, and then press the
OK
button.
2.
Select
Paper Handling Setup
, and then press the
OK
button.
3.
Select
Fuser Configuration
, and then press the
OK
button.
4.
Select the appropriate media, and then press the
OK
button.
5.
Select the desired fuser temperature,
Extra High
,
Very High
,
High
,
Medium
,
Low
, or
Very
Low
and then press the
OK
button.
Using CentreWare IS
To select the fuser temperature using CentreWare IS:
1.
Launch your web browser.
2.
Enter the printer’s IP address in the browser’s
Address
3.
Click
Properties
.
4.
Select
General
on the left navigation panel, and then select
Fuser
.
5.
Use the appropriate media drop-down list to change the fuser temperature.
6.
Click the
Save Changes
button at the bottom of the page.