Xerox 6180N Getting Started v3.74 - Page 25

Copy Sensitive CME support, Auto End changes and moves

Page 25 highlights

DOCUSP 3.74 Copy Sensitive CME support ¨ Copy sensitive CMEs will be honored. The LCDS PDL allows individual copies of a report to contain changes from the original report by the use of copy sensitive form, RTEXT, and CMEs. Copy sensitive CMEs allow certain parts of the report to be modified on selected copies with new or replacement static text or with the specification of font or ink changes within the variable data. · On the LPS printers, this was accomplished by performing multiple passes over the data. Therefore, only offline tape jobs could contain copy sensitive CME's. · On EPS printers, copy sensitive CMEs are supported with spooling queues only. The job may originate from Online, Tape, or the Socket gateway. However, if the job is extremely large, the spool may become full. The spool is limited by the available hard disk space. The entire job must be spooled to disk before the decomposer can begin ripping. Auto End changes and moves ¨ In previous versions, the operator needed to press "Start" to start an online job and press "End" to finish the job. The operator needed to be present to press "End" so that network jobs could be scheduled and printed. ¨ The AutoEnd feature allows: · Online jobs to automatically end and start based on a timer set in the Online Gateway configuration. · Online jobs automatically end and start based on the receipt of the channel command 0x6b (raise cover) in the datastream. ¨ Now the AutoEnd feature invokes the "End" for the current job and starts a new job without operator intervention. ¨ The System Administrator enables AutoEnd. By default, the AutoEnd feature is disabled. ¨ AutoEnd is supported in both streaming and spooling modes. ¨ AutoEnd and AutoDrain with a timer cannot be set at the same time. XEROX DOCUMENT SERVICES PLATFORM SERIES GETTING STARTED 3-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54

DOCUSP 3.74
XEROX DOCUMENT SERVICES PLATFORM SERIES
3-11
GETTING STARTED
Copy Sensitive CME support
²
Copy sensitive CMEs will be honored. The LCDS PDL allows
individual copies of a report to contain changes from the
original report by the use of copy sensitive form, RTEXT,
and CMEs. Copy sensitive CMEs allow certain parts of the
report to be modified on selected copies with new or
replacement static text or with the specification of font or ink
changes within the variable data.
³
On the LPS printers, this was accomplished by
performing multiple passes over the data. Therefore,
only offline tape jobs could contain copy sensitive
CME’s.
³
On EPS printers, copy sensitive CMEs are supported
with spooling queues only. The job may originate from
Online, Tape, or the Socket gateway. However, if the job
is extremely large, the spool may become full. The spool
is limited by the available hard disk space. The entire job
must be spooled to disk before the decomposer can
begin ripping.
Auto End changes and moves
²
In previous versions, the operator needed to press “Start” to
start an online job and press “End” to finish the job. The
operator needed to be present to press “End” so that
network jobs could be scheduled and printed.
²
The AutoEnd feature allows:
³
Online jobs to automatically end and start based on a
timer set in the Online Gateway configuration.
³
Online jobs automatically end and start based on the
receipt of the channel command 0x6b (raise cover) in
the datastream.
²
Now the AutoEnd feature invokes the “End” for the current
job and starts a new job without operator intervention.
²
The System Administrator enables AutoEnd.
By default, the
AutoEnd feature is disabled.
²
AutoEnd is supported in both streaming and spooling
modes.
²
AutoEnd and AutoDrain with a timer cannot be set at the
same time.