Yamaha AW2816 Owner's Manual - Page 392
Automix cannot be recorded, t use the internal effects - troubleshooting
View all Yamaha AW2816 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 392 highlights
Troubleshooting s MMC messages is not transmitted • Is the MIDI cable connected to the MIDI OUT con- nector? • MMC messages are not transmitted from the MTC OUT connector. s Can't receive MMC messages • Is the MIDI cable connected to the MIDI IN con- nector? • MMC messages cannot be received if the AW2816 is functioning as the MTC slave. s MIDI data is not exchanged via the TO HOST connector • Is the cable correctly connected to the TO HOST connector? • PORT SELECT may be set to MIDI. • Is the PORT SELECT setting appropriate for your computer? * * For details on this setting, refer to page 272 "MIDI screen." • A computer application other than your sequencer may be using the port. s Metronome cannot be heard • The metronome sound is normally sent only to the MONITOR OUT and headphones. * * Settings can also be made in the SETUP screen Patch IN page to assign the metronome to an output channel. s Moving a fader does not change the level • Is the appropriate fader mode and mixing layer selected? • The fader may be set to PRE FADE in AUX. s The ON key and SEL key select the wrong channel • Is the appropriate mixing layer selected? s Noise is present in the recorded signal • Does the word clock setting match for the AW2816 and the external device(s)? • Is an unsynchronized signal being input? • Is the dither setting appropriate? • The oscillator may be functioning. • If the speed of your internal hard disk is slow, prob- lems may occur during recording and playback. Please use only the recommended internal hard disks. s Sound recorded via the digital input sounds grainy • Is the dither setting appropriate? s Pairing was specified, but the signal is monaural • Is the odd-numbered channel panned far left and the even-numbered channel panned far right? s Pairing was specified, but the signal phase does not match • Even when channels are paired, the phase setting is not linked. s Signal is delayed • Is the channel delay set correctly? s Automix cannot be recorded • Is automix set to ENABLE? • In the AUTOMIX screen, is the REC or AUTO REC button turned ON? • Is the [SEL] key lit for the channel you are operat- ing? • Is OVERWRITE turned ON for the control (e.g., fader or EQ) you are operating? s Can't use the internal effects • Effect BYPASS may be turned ON. • Are the level of EFF.RTN 1, 2 faders raised? • In the SETUP screen Patch IN page, EFFECT PATCH may be set to INSERT. • It is not possible to insert one effect into multiple channels. • 019. HQ. Pitch can be used only with EFFECT 2. s Can't use SOLO • The channel may be set to Solo Safe. • Is the SETUP screen Solo Setup page set appropri- ately? * * For details on the settings, refer to "SETUP screen." s Can't edit a recorded track • Have you selected the virtual track that you recorded? s Fader groups and mute groups don't work • In the EQ screen Fader Group page and Mute Group page, check that grouping is set to ENABLE. s Editing results are not heard in the sound • Have you selected the virtual track that you recorded? • Are you using the appropriate editing command? * * For details on editing commands, refer to "EDIT screen." s Playback pitch is wrong • VARI may be selected. • Is the AW2816 operating on the same sampling fre- quency as the synchronized external device? • Is the master device operating in a stable way? • You may have executed the EDIT screen PITCH command. • Is an effect such as HQ.Pitch or Dual Pitch selected for a monitor channel? s Counter display is not 0 when you return to the beginning of the song • The display mode may be set to REMAIN (remaining recording time). • If the display mode is set to REL (relative time), the start point may be specified. • The SONG screen Setting page may be set to MEASURE. * * For details on this setting, refer to "SONG screen." 390 Appendix