Yamaha CLP-280 Owner's Manual - Page 111

Attach

Get Yamaha CLP-280 PDF manuals and user guides View all Yamaha CLP-280 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

3-3 Align the dimple on side A with the inner side of E and F. Simultaneously lower the left and right side of A, and secure with E and F. CAUTION Fingers can become pinched between the main unit and the rear or side panels, be extra careful so as not to drop the main unit. CAUTION Do not hold the keyboard in any position other than the position shown in the illustration. CLP-280/270: Keyboard Stand Assembly 4. Attach A. 4-1 Secure A using two 6 x 16mm short screws from the rear. 4-2 Secure A using four 6 x 16mm short screws from the front. 4-3 Firmly tighten the screws you temporarily secured in step 2-4 above (assembly B). Tighten these in order starting with the top side first, then the bottom. Make sure as you do this that the spaces on the left and right sides (indicated by 1 and 2 below) are even. 4-2 Place your hands at least 10 cm from either end of A when positioning it. 3-4 Support the backside of E and F with your hand, and slightly push A in from the keyboard side until it stops. 4-3 Appendix 3-5 Remove the side panel protection pad. CLP-280/270 Owner's Manual 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
CLP-280/270 Owner’s Manual
111
Appendix
CLP-280/270: Keyboard Stand Assembly
3-3
Align the dimple on side A with the inner side
of E and F. Simultaneously lower the left and
right side of A, and secure with E and F.
3-4
Support the backside of E and F with your
hand, and slightly push A in from the keyboard
side until it stops.
3-5
Remove the side panel protection pad.
4.
Attach A.
4-1
Secure A using two 6 x 16mm short screws
from the rear.
4-2
Secure A using four 6 x 16mm short screws
from the front.
4-3
Firmly tighten the screws you temporarily
secured in step 2-4 above (assembly B).
Tighten these in order starting with the top side
first, then the bottom. Make sure as you do this that
the spaces on the left and right sides (indicated by
1
and
2
below) are even.
CAUTION
Fingers can become pinched between the main unit and
the rear or side panels, be extra careful so as not to drop
the main unit.
CAUTION
Do not hold the keyboard in any position other than the
position shown in the illustration.
Place your hands
at least 10 cm from either
end of A when positioning it.
4-2
4-3