Yamaha PSR-1700 Owner's Manual - Page 84

System Reset Procedure

Get Yamaha PSR-1700 PDF manuals and user guides View all Yamaha PSR-1700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

Appendix Digital Sampling-related Error Messages (PSR-2700) No Bank No Wave Data Protected Voice Same Note Wave Ram Full Wrong Disk The maximum of 255 "banks" of data has been exceeded (one pad contains one "bank"). Clear all unnecessary pads and voice data before attempting to sample more data. You have attempted to map or tune a pad or entering an original voice name that contains no sampled voice data. You have attempted to clear, record, or edit a pre-programmed disk voice file. In some cases pre-programmed sampled voices ("Protected Voices") can only be loaded. You have attempted to map a pad to key to which another pad is already mapped. Map either pad to a different key. The wave RAM memory is full and can accept no more sampled voice data (the wave RAM is 1,020 kilobytes). Clear all unnecessary pads and voice data before attempting to sample more data. You have inserted the wrong disk or a disk that does not contain the required data. Large sampled voice data files may span more than one disk, and these must be inserted in the correct order when loading the file. Check the disk number and try again. Other Error Messages IllegalOperation Memory Full You have pressed a button that can not be used in the current mode. Read the instructions for the function you are using carefully, and use appropriate function button. The PSR-1700/2700 recording memory has become full while recording Song Memory, Custom Accompaniment, or Multi Pad data. Save data you want to keep to disk and clear all unnecessary data from memory to make more room. s System Reset Procedure All internal memory settings are retained in memory even when the power switch is turned OFF as long as a good set of backup batteries is present or the AC plug is connected. You can, however, restore the factory default settings by following the procedures outlined below. ON/ OFF POWER -+ RESET ZPress the [POWER] switch to turn the PSR-1700/PSR-2700 power OFF. XTurn the power back ON while holding both the [+] and [-] buttons. "Backup RAM Clear" will appear on the LCD display panel while the data is being reset. IMPORTANT • Executing the System Reset function will erase all internal memory settings 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
Appendix
The maximum of 255 “banks” of data has been exceeded (one pad contains one “bank”).
Clear all unnecessary pads and voice data before attempting to sample more data.
You have attempted to map or tune a pad or entering an original voice name that contains
no sampled voice data.
You have attempted to clear, record, or edit a pre-programmed disk voice file. In some
cases pre-programmed sampled voices (“Protected Voices”) can only be loaded.
You have attempted to map a pad to key to which another pad is already mapped. Map
either pad to a different key.
The wave RAM memory is full and can accept no more sampled voice data (the wave RAM
is 1,020 kilobytes). Clear all unnecessary pads and voice data before attempting to sample
more data.
You have inserted the wrong disk or a disk that does not contain the required data. Large
sampled voice data files may span more than one disk, and these must be inserted in the
correct order when loading the file. Check the disk number and try again.
No
°
Bank
No
°
Wave
°
Data
Digital Sampling-related Error Messages (PSR-2700)
Wave
°
Ram
°
Full
Protected
°
Voice
Same
°
Note
Wrong
°
Disk
Other Error Messages
You have pressed a button that can not be used in the current mode. Read the instructions
for the function you are using carefully, and use appropriate function button.
IllegalOperation
The PSR-1700/2700 recording memory has become full while recording Song Memory,
Custom Accompaniment, or Multi Pad data. Save data you want to keep to disk and clear
all unnecessary data from memory to make more room.
Memory
°
Full
■
System Reset Procedure
All internal
memory settings are retained in memory even when the power switch is turned OFF as long as a
good set of backup batteries is present or the AC plug is connected. You can, however, restore the factory default
settings by following the procedures outlined below.
–
+
RESET
POWER
ON/
OFF
Z
Press the
[POWER]
switch to turn the PSR-1700/PSR-2700 power OFF.
X
Turn the power back ON while holding both the
[+]
and
[–]
buttons.
“Backup RAM Clear” will appear on the LCD display panel while the
data is being reset.
IMPORTANT
•
Executing the System Reset function will erase all internal
memory settings